background image

428 01 1703 01  

6/17/13

Specifications subject to change without notice.

INSTALLATION INSTRUCTIONS

R

410A Two

Stage Split System Heat Pumps

CCH9, HCH9, TCH9

CCH6, HCH6, TCH6

These instructions must be read and understood completely before attempting installation.

DANGER, WARNING, CAUTION, and

NOTE

The signal words

 DANGER, WARNING,

CAUTION, 

and

 NOTE

 are used to identify levels of

hazard seriousness. The signal word 

DANGER

 is

only used on product labels to signify an immediate

hazard. The signal words

 WARNING,

 

CAUTION,

and

 NOTE

 will be used on product labels and

throughout this manual and other manuals that may

apply to the product.

DANGER

 

 Immediate hazards which 

will

 result in

severe personal injury or death.

WARNING 

 Hazards or unsafe practices which

could

 result in severe personal injury or death.

CAUTION 

 Hazards or unsafe practices which

may

 result in minor personal injury or product or

property damage.

NOTE 

 Used to highlight suggestions which 

will

result in enhanced installation, reliability, or

operation.

Signal Words in Manuals

The signal word

 WARNING 

is used throughout this

manual in the following manner:

The signal word 

CAUTION 

is used throughout this

manual in the following manner:

Signal Words on Product Labeling

Signal words are used in combination with colors

and/or pictures on product labels.

WARNING

Safety Labeling and Signal Words

!

CAUTION

WARNING

!

TABLE OF CONTENTS

Safety Considerations

2

. . . . . . . . . . . . . . . . . . . . . . . . . . .

Installation Recommendations

2

. . . . . . . . . . . . . . . . . . .

Installation

2

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Start

up Procedure

7

. . . . . . . . . . . . . . . . . . . . . . . . . . . . .

System Functions & Sequence of Operation

9

. . . . . . .

Defrost

10

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Troubleshooting

11

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Status Codes

15

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

R

410A Quick Reference Guide

16

. . . . . . . . . . . . . . . . .

!

WARNING

ELECTRICAL SHOCK HAZARD
Failure to follow this warning could result in per-

sonal  injury and/or death.
Before installing, modifying, or servicing system,

main electrical disconnect switch must be in the

OFF position. There may be more than 1 discon-

nect switch. Lock out and tag switch with a suit-

able warning label.

!

CAUTION

CUT HAZARD
Failure to follow this caution may result in per-

sonal injury
Sheet metal parts may have sharp edges or burrs.

Use care and wear appropriate protective clothing

and gloves when handling parts.

Summary of Contents for CCH9

















Reviews: