background image

Product Numbers: 6372, 6372OV

Davis Instruments Part Number: 07395.239
 
Wireless Temperature Station 2 Installation Manual 
Rev. A Manual (11/29/04)

This product complies with the essential protection requirements of the EC EMC Directve 89/336. 

3465 Diablo Avenue, Hayward, CA 94545-2778

510-732-9229 • Fax: 510-732-9188

E-mail: [email protected]  •  www.davisnet.com

FCC Part 15 Class B Registration Warning

This equipment has been tested and found to comply with the limits for a 
class B digital device, pursuant to Part 15 of the FCC Rules. These limits 
are designed to provide reasonable protection against harmful interference 
in a residential installation. This equipment generates, uses and can radiate 
radio frequency energy and, if not installed and used in accordance with the 
instructions, may cause harmful interference to radio communications. 
However, there is no guarantee that interference will not occur in a particu-
lar installation. 

If this equipment does cause harmful interference to radio or television      
reception, which can be determined by turning the equipment off and on, 
the user is encouraged to try to correct the interference by one or more of 
the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to 

which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

Changes or modifications not expressly approved in writing by Davis 
Instruments may void the user's authority to operate this equipment.

Summary of Contents for Wireless Temperature Station













Reviews: