manualshive.com logo in svg

DAVIS Wireless Temperature/Humidity Station, Instruction Manual, Page: 9 / 16

Share
Download
DAVIS Wireless Temperature/Humidity Station Instruction Manual Download Page 9

 

Setting the DavisTalk Transmitter ID

Page 9

 

4.

Check the Junction Board cable connections: SIM Sensor, SIM Power (SIM), 
Motor, Temp/Hum Sensor, and Solar Panel (SOL). 

5.

Install the Junction Board Cover as show below. The Junction Board Cover 
presses easily into place when you are installing it. To remove the cover, 
press gently in on both sides to release the latches holding it in place.

6.

Slide the two sections of the Radiation Shield completely together.

7.

Place the flat washers, lock washers and plastic wing nuts over the 
threaded rods.

8.

Finger-tighten the wing nuts until they hold the radiation shield plates 
firmly in place.

S

I

M

Sensor

Interface 

Cable

SIM

Power 

Cable

Solar 

Panel
Cable

S

O

L

Junction Board Cable Connections

Junction Board Cover

Junction Board

Press in on Sides

near latches 

to Remove Cover

Junction Board Cover Installation

Summary of Contents for Wireless Temperature/Humidity Station

















Reviews:

No comments