background image

Product # 6361

W

IRELESS

 

S

OIL

 M

OISTURE

T

EMPERATURE

 S

TATION

I

NSTALLATION

 M

ANUAL

The Wireless Soil Moisture/Temperature Station, referred to in this document 
as the Soil Moisture Station, is for use with Wireless Vantage Pro

® 

Weather Sta-

tions. One Soil Moisture Station can be installed per Vantage Pro Weather Sta-
tion. Up to four WATERMARK soil moisture sensors and four multi-
temperature probes can be installed in a Soil Moisture Station.

Note: The Soil Moisture Station requires Vantage Pro console firmware dated Oct 25 

2001 or later. (Press and hold the DONE key then press the UP arrow (+) key to 
display the console firmware level.) Contact Davis Technical Support if your 
console requires an upgrade. Contact information is located in the back of this 
manual.

Components

The Soil Moisture Station includes the following components and mounting 
hardware:

Soil Moisture Sensor

with 15' (4.6 m) of cable

Temperature Probe

with 15' (4.6 m) of cable

Shelter

3-Volt Lithium Battery

8" Cable Ties

4" Cable Ties

Soil Moisture Station Components

Summary of Contents for Soil Moisture/Temperature Station

















Reviews: