manualshive.com logo in svg

DAVIS DriveRight 8156GD, Installation Manual

Share
Download
DAVIS DriveRight 8156GD Installation Manual Download Page 16

7RSRI'DVKERDUG0RXQWLQJ2SWLRQV

Instructions for Using Velcro

®

:

Apply the two adhesive-backed Velcro loop tapes to the flats on the back of 
the console or to the back of the bracket.

Attach the hook tapes to the loop tapes, then press adhesive backing of the 
hook tape onto your selected mounting surface. 

1RWH

Do not separate the Velcro for at least 24 hours after applying. 

6XQ9LVRU0RXQWLQJ

Use the visor clip to mount your console on a visor or door pocket. 

Install the clip on the top or bottom of the console to orient the console as 
you wish. 

Push the clip in until the 3rd bump engages.

Pan Head Self-Tapping Screw

Split-Lock Washer

Flat Washer

Hex Nut

Split-Lock Washer

Flat Washer

Right Angle

Adapter Bracket

Mounting Bracket

Flat Head Machine Screw

Bracket Mounting

Loops

Hooks

Velcro Mounting

3 Bumps 

(to hold clip)

OR

Visor Clip

07395.043 DR GD Inst Rev D Body D146.fm  Page 14  Monday, December 1, 2003  12:02 PM

Summary of Contents for DriveRight 8156GD

























Reviews:

No comments

Brands by name

Popular brands

Load more brands