manualshive.com logo in svg

Davis Instruments Vantage Vue 6242, Installation Manual, Page: 3 / 16

Share
Download
Davis Instruments Vantage Vue 6242 Installation Manual Download Page 3

1

Introduction

The Vantage Vue® wireless sensor suite collects outside weather data and sends the data 
wirelessly to a Vantage Vue console via a low-power radio. The sensor suite is solar-
powered and includes a battery back-up. 

The Vantage Vue sensor suite contains a rain collector, temperature/humidity sensor, 
anemometer, and wind vane. The temperature/humidity sensor is mounted in a passive 
radiation shield to minimize the impact of solar radiation on sensor readings. The 
anemometer measures wind speed, and the wind vane measures wind direction. 

The Sensor Interface Module (SIM) is housed within the sensor suite and comprises the 
“brains” of the Vantage Vue system and the radio transmitter. The SIM collects outside 
weather data from the sensor suite sensors and transmits that data to your Vantage Vue 
console or WeatherLink Live. 

Note: 

Your Vantage Vue sensor suite can transmit to an unlimited number of consoles, so you can 
purchase additional consoles to use in different rooms. It can also transmit to Davis Vantage Pro2 
consoles, WeatherLink Live, and Davis Weather Envoys as well as Vantage Vue consoles. 

Included Components and Hardware

Vantage Vue Sensor Suite Components

Wind cups

Tipping spoon 
(rain) assembly

Wind vane

Rain collector 
debris screen

Solar panel

Radiation
shield

Summary of Contents for Vantage Vue 6242

















Reviews:

No comments