background image

Extending Cable Runs

10

To Clear Rainfall

Daily and total rainfall are independent of each other. You must clear each register 
separately.

1. Press RAIN once or twice to select daily or total rainfall, as desired.

2. Press CLEAR and hold it down.

The display will flash several times and then the weather station clears rainfall.

Daily Rainfall Cleared

Note:  Performing a “total clear” on the weather station does not clear rainfall.

To Set Total Rainfall

You may enter a total rainfall amount to represent any rainfall which accumulated before 
you obtained the Rain Collector II:

1. Press RAIN once or twice to select total rainfall.

2. Use ENTER to set the total rainfall amount. See “Using the Enter Key” in the weather 

station manual.

Calibration of Older Model Weather Stations 

This information applies only to users of the Weather Wizard II-S, Weather Wizard III, 
and Weather Monitor II manufactured prior to April, 1993. To check if your station meets 
this criterion, press the RAIN button on the console. If, when set to inches, the display 
reads 0.0 (rather than 0.00), you have an older model station. 

Standard Setting

When using the 0.01” setting of the Rain Collector II with an older model station, note 
that the station is pre-calibrated for an earlier model 0.1" rain collector. To re-calibrate 
your station, first set the display to inches, then change CAL to 0100. (See “Rainfall Cal-
ibration Number” on page 2 and/or your station user’s manual for instructions on how to 
change CAL.) Be aware that the console will revert to its default calibration (i.e., 0.1") if 
it loses power.

Metric Setting

When using the 0.2 mm setting of the Rain Collector II with an older model station, note 
that the station stores rainfall amounts in 0.2 mm increments but displays amounts 
rounded to the nearest whole millimeter. 

Note:  Keep in mind when testing the rain collector with older weather stations that the display adds   1 mm for 

each 5 tips of the bucket. Because the display rounds, however, the first change occurs after the bucket 
tips 3 times (0.6 mm rounded to 1 mm).

Summary of Contents for 7852

















Reviews: