background image

1. PUMP TO THE FILTER

Monarch Series Cartridge Filters are equipped with two inlet ports 

marked ‘INLET’. Select the inlet port most suitable for the installation 

and plug the other inlet port with the blanking cap provided. Using 

the barrel unions provided, connect the pool pump delivery piping 

to the selected inlet port. Tighten by hand only. Ensure the oring on 

the fitting is clean, lubricated with oring lubricant and in the correct 

position.

2. FILTER TO POOL RETURN

Using quick connect couplings, connect the pool return piping 

to the filter fitting marked ‘OUTLET’. Tighten the fitting by hand 

only. Ensure the oring on the fitting is clean, lubricated with oring 

lubricant and in the correct position.

The filter base is provided with four mounting holes to enable it to 

be secured, if required.

FILTER OPERATION

-AKESURETHEPUMPISPRIMEDACCORDINGTOMANUFACTURERS

directions.

"ESUREALLVALVESAREOPENONSUCTIONANDDISCHARGELINES

Ensure the air bleed valve on the filter lid is open and the lid 

lock ring is in place and secure.

3TARTTHEPUMP#LOSETHEAIRBLEEDVALVEWHENWATERIS

expelled.

4. 

To determine the correct operating conditions with a clean 

lLTERCHECKTHATTHEPRESSUREGAUGEREADINGISK0AORBELOW

5. 

Record the pressure gauge reading or mark the needle 

position on the face of the pressure gauge.

6. 

Operate the filter for a sufficient time to circulate the total 

pool water volume daily. The filter should also be operated 

at all times the pool is in use and for about one hour 

afterwards. During winter, the running time may be reduced. 

Filter operating requirements will vary for spa applications, 

depending upon the system design, type and size of spa.  

Consult your builder or spa supplier.

7HENTHEPRESSUREGAUGEREADINGISK0AHIGHERTHAN

the ‘clean filter’ reading as in (4) above, it is time to clean the 

element/s. (See “Cartridge cleaning procedure”)

s0AGEs

Summary of Contents for Monarch EcoPure Q2201MN











Reviews: