manualshive.com logo in svg

Datex-Ohmeda D-VHC17, Technical Reference Manual

Share
Download
Datex-Ohmeda D-VHC17 Technical Reference Manual Download Page 31

Displays and Controller Boards

Document No. 8001004-1

25

3.

 

Check external parts:

−

 

the outer cover is intact

−

 

the display screen is intact

−

 

the front panel stickers are intact

−

 

the ComWheel cover is intact and is attached properly

−

 

the ON/STBY -switch and its protector are intact and are attached properly

−

 

the anesthesia keyboard connector is clean and intact

−

 

the LCD interface cable connector is clean and intact

−

 

the block screws for the cable are in place and are tightened properly (if installed)

−

 

the block screw threads are intact (if installed)

?

4.

 

Check that the ON/STBY -switch changes its state firmly when switching it back and forth.

Leave the switch into STBY -position.

?

•

 

Turn the monitor to stand-by. Install the M-NE(12)STPR/M-ESTPR/M-ESTP to the Central

Unit.

•

 

Connect and lock the LCD interface cable to the LCD display and to the used B-DISP/B-

DVGA in the monitor.

5.

 

Check that the stand-by LED on the LCD display front panel is lit up (the monitor power cord is

connected to the mains).

?

•

 

Turn the LCD display ON/STBY -switch to ON.

?

6.

 

Wait until normal monitoring screen appears onto the LCD display. Check that the picture on the

LCD display screen is clear and stable. Check also that all the colors are clear.

?

Summary of Contents for D-VHC17









































































Reviews:

No comments

Brands by name

Popular brands

Load more brands