background image

Turntable / Line Channels (3 , 4 and 5)

These three stereo channels each have two inputs (Phono for turntables and Line for equipment like
CD-players and MD-recorders), volume control, 3-way tone control, crossfader routing selector and
pre-fader listening.

Phono / Line

Input selector. Normally the Phono input is selected. Pushed
in is Line (CD, MD, tape). LEDs indicate which input is
selected.

GAIN

Determines the pre-adjustment of the volume for both the
Phono as well as the stereo Line input.

Dual Line Channels (6 and 7)

These channels have an input selector for the two identical stereo line inputs (for equipment like CD-
players and MD-recorders), volume control, 3-way tone control, crossfader routing selector and pre-
fader listening.

Line 1 / Line 2

Input selector. Normally the Line 1 (CD, MD, tape) input is
selected. Pushed in is Line 2. LEDs indicate which input is
selected.

GAIN

Determines the pre-adjustment of the volume for both the Line
1 as well as the Line 2 input.

Crossfader and Transform

Normally all channels are mixed directly to the master output
(with the A/ MASTER/ B-switch in the centre position).
However, the channels can also be sent via the A- or B-side
of the crossfader to the master. Channels via the A-side
cannot be heard with the crossfader in the outmost right
position. Channels via the B-side cannot be heard with the
crossfader in the outmost left position. The crossfader curve
can be adjusted with the trimmer.

LEDs A and B above the crossfader indicate if the signal is switched to the A-side or the B-side of
the cross-fader with a crossfader routing select switch. This avoids mistakes, because you can see
immediately if there has been a channel selected on both sides.

With the transform ON-switch pushed in (the transform ON-LED lights up), both the A- and the B-side
of the crossfader will not be heard on the master output. Both crossfader-signals will now only be
passed on if the transform-switch is pushed in. In this way short fragments can be made audible in a
very simple way.

TRAN SFORM

TEMPO

SYNC

BEATCOMPARE

P Controlled

ON

A

B

P

Summary of Contents for Apollo












Reviews: