background image

3

 

 

FCC Compliance Statement 

This  device  complies  with  part  15  of  the  FCC  rules.  Operation  is  subject  to 
the following two conditions: 

(1)

 

This device may not cause harmful interference, and   

(2)

 

This  device  must  accept  any  interference  received,  including 
interference that may cause undesired operation. 

Warnings and Precautions 

1.

 

Read  all  of  these  warnings  and  save  them  for  later 
reference. 

2.

 

Follow all warnings and instructions marked on this unit. 

3.

 

Unplug  this  unit  from  the  wall  outlet  before  cleaning. Do 
not use liquid or aerosol cleaners. Use a damp cloth for cleaning. 

4.

 

Do not use this unit in or near water.   

5.

 

Do not place this unit on an unstable cart, stand, or table. The unit may 
fall, causing serious damage. 

6.

 

Slots  and  openings  on  the cabinet  top,  back,  and  bottom are  provided 
for ventilation. To ensure safe and reliable operation of this unit, and to 
protect  it  from  overheating,  do  not  block  or  cover  these  openings.  Do 
not  place  this  unit  on  a  bed,  sofa,  rug,  or  similar  surface,  as  the 
ventilation openings on the bottom of the cabinet will be blocked. This 
unit should never be placed near or over a heat register or radiator. This 
unit  should  not  be  placed  in  a  built-in  installation  unless  proper 
ventilation is provided. 

7.

 

This  product  should  only  be  operated  from  the  type  of  power  source 
indicated on the marking label of the AC adapter. If you are not sure of 
the type of power available, consult your Datavideo dealer or your local 
power company. 

8.

 

Do not allow anything to rest on the power cord. Do not locate this unit 
where  the  power  cord  will  be  walked  on,  rolled  over,  or  otherwise 
stressed. 

9.

 

If  an  extension  cord  must  be  used  with  this  unit,  make  sure  that  the 
total of the ampere ratings on the products plugged into the extension 
cord do not exceed the extension cord rating. 

10.

 

Make sure that the total amperes of all the units that are plugged into a 
single wall outlet do not exceed 15 amperes. 

11.

 

Never  push  objects  of  any  kind  into  this  unit  through  the  cabinet 
ventilation  slots,  as  they  may  touch  dangerous  voltage  points  or  short 

Summary of Contents for CG-350TC Kit





















Reviews: