background image

MAINTENANCE

TRANSMITTER

The transmitter contains delicate electronic
circuits and must be protected from impact and
water damage. Do not remove soft plastic body
until batteries need replacing.

Low Transmitter Battery State

If three long tones are heard when the
transmitter operates, the transmitter batteries
need replacing.

REPLACE THE BATTERIES (two CR2016) as
soon as possible. Failure to do so will mean that
you are unable to disarm the system, and your
motorcycle will be immobilised (see pin override).

Replacing Transmitter  Batteries

Clean the battery contacts and make sure that
the replacement batteries are of the correct type
and located in the correct position with the
polarity maintained.

New Transmitters

If one of your transmitters has been lost or
damaged, a new transmitter can be supplied. The
new transmitter will automatically cancel the lost
or damaged transmitter, so only two functioning
transmitters can ever exist. Contact your supplier
for full details of this service.

CONTROL UNIT

The control unit also contains delicate electronic
circuits and must never be pressure washed or
steam cleaned.

MOTORCYCLE BATTERY

If the battery level falls, the alarm system is
equipped with ‘intelligent sleep mode’.

Intelligent battery chargers and optimisers are
available to maintain the motorcycle battery in
top condition, recommended types are Optimate
(DATATOOL Part No 02012011) and Airflow
(DATATOOL Part No 02012009). DATATOOL does
not recommend that any other charging device is
used unless the system has been put in
SERVICE MODE and the IN-LINE Fuse has
been removed prior to connection of the charging
device.

Contact your DATATOOL Installer for further
information.

GENERAL SECURITY

The DATATOOL alarm/immobiliser system will
provide an effective deterrent against theft. It will
not in itself guarantee that your motorcycle is not
stolen or damaged. We strongly advise that your
DATATOOL System is used in conjunction with
basic anti-theft precautions.

ACCESSORIES

A range of accessories are available to extend
the performance of your system. These are
available from your dealer or importer and
include:

Additional Remote Transmitters

Pocket Paging Alert (Available only in certain
countries)

Intelligent Battery Charger

WARRANTY TERMS AND CONDITIONS

Full written details of the Warranty Terms and
Conditions will be given to you by the DATATOOL
Authorised Installer.

BE SURE TO RETURN YOUR CERTIFICATE

OF INSTALLATION

DATATOOL Products are designed and produced in the UK by Datatool (UK) Ltd

Anstey Mill Lane, Alton, Hampshire GU34 2QQ United Kingdom

Telephone: +44 (0) 1420 541444   Fax: +44 (0) 1420 541447

Email: [email protected]  web: www.datatool.co.uk

FCC:
This device complies with Part 15 of the FCC rules.
Operation is subject to the following two
conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any
interference received, including interference that
may cause undesired operation.
Any changes or modifications not expressly
approved by the party responsible for compliance
could void the user's authority to operate the
equipment.

Summary of Contents for system 21













Reviews: