background image

OC-3 SERIES OF PRINTERS USER'S GUIDE

10

Printing a self-test

1. Press and hold the power button for approximately three (3) 

seconds until printing begins. For information on button 

functions, see "Using the control panel" on page 13.

2. After printing begins, release the power button. A self-test 

label will print showing parameters, as described on 

page 11.

Connecting the printer via a cable or radio

The OC-3 printer is designed to transmit and receive data from 

a host terminal. The host terminal may be your computer, 

handheld, or laptop. Communication can occur using one of the 

following methods:

Using a data cable to connect the printer and the host 

terminal ("Installing a data cable" on page 10), or 

Enabling wireless communication (see "Bluetooth and/or 

802.11b parameters" on page 11).

Installing a data cable

1. Verify the printer settings before connecting the printer to a 

host terminal. For more information, see "Printing a self-

test" on page 10.

2. Insert the data cable plug into the printer's data port (Figure 

25).

3. Connect the data cable to the host or device you are using.

Removing a data cable

1. Rotate the printer so that the printer's data port is visible.
2. Lift the cable connector's lever and remove the cable. 

Figure 24

Figure 25

Data port

Summary of Contents for OC-3 Series





























Reviews: