Datalogic S5N-M PP Series Instruction Manual Download Page 1

Page: 1 / 7

This product is covered by one or more of the following patents.

European Patent 851,211 B1; 1,111,690 B1; 1,148,346 B1; 1,209,487 B1.

Italian Patent IT 1,321,772.

S5N-Mx-

…-PP/NN SERIES

INSTRUCTION MANUAL

CONTROLS

OUTPUT LED (S5N-

Mx…A00/B01/C01/C10/C21/D00/E01/F01/T01)

The yellow LED ON indicates that the N.O. (normally open) output
status is closed.

STABILITY LED (S5N-

Mx…B01/C01/C21/E01/F01)

The green LED ON indicates that the received signal has a reserve
greater than 30% compared to the output switching value.

POWER ON LED (S5N-

Mx…G00)

The green LED indicates that the sensor is operating.

TRIMMER (S5N-

Mx…B01/C01/C21/E01/F01/T01)

The trimmer can be used to adjust sensitivity; the operating distance
increases turning the trimmer clockwise.

WARNING: The trimmer rotation is limited to 270° by a mechanical stop.
Do not apply excessive torque when adjusting (max 40 Nmm).

INSTALLATION

The sensor can be fixed by means of the M18x1 threaded body through
a



18 mm hole, using the two CH.24 nuts enclosed (22 Nm maximum

tightening torque).
Wide range of accessories available: various orientable fixing brackets
ease the sensor positioning (please refer to the accessories listed in the
general catalogue).
The operating distance is measured from the front surface of the sensor
lens.

C models

: To improve the detection, the

object has to be moved closer or further away
from the front surface of the sensor lens.

In case of lateral translation, the object must
move as indicated in the figure.

CONNECTIONS

The connections are compliant to the EN 60947-5-2 standard.

10 … 30 Vdc

N.C. OUTPUT

BROWN

WHITE

BLACK

BLUE

N.O. OUTPUT

0 V

S5N-

Mx…G00

10 … 30 Vdc

TEST +

BROWN

WHITE

BLACK

BLUE

TEST -

0 V

M12 CONNECTOR

DIMENSIONS

RADIAL VERSION

FIBRE OPTIC VERSION

57
38

without trimmer

L
X

M O D E L S

with trimmer

67
43

AXIAL VERSION

69
38

without trimmer

L
X

M O D E L S

with trimmer

79
43

CABLE VERSION

M18x1

2.5

TRIMMER

M12

Ø4

OUTPUT LED

STABILITY LED

6.2

M18x1

2.2

TRIMMER

54.5

M12

STABILITY LED

OUTPUT LED

STABILITY LED

OUTPUT LED

LED STABILITY

LED DI USCITA

6°

14.5

M18x1

M12

14.5

72.5

14.5

TRIMMER

TECHNICAL DATA

S5N-MA AXIAL VERSION

S5N-MR RADIAL VERSION

Power supply:

10 … 30 Vdc (limit values)

Ripple:

2 Vpp max.

Current consumption
(output current excluded):

35 mA max.

Outputs:

N.O. and N.C.; PNP or NPN

(short-circuit protection)

Output current:

100 mA max.

Output saturation voltage:

2 V max.

Response time:

0.5 ms (2 ms mod.F01/G00)

Switching frequency:

1 kHz (250 Hz mod.F01/G00)

Indicators:

OUTPUT LED (YELLOW) excluding mod.G00

STABILITY LED (GREEN) (mod.B01/C01/C21/E01/F01)

POWER ON LED (GREEN) (mod.G00)

Setting:

sensitivity trimmer (mod.B01/C01/C21/E01/F01/T01)

Operating temperature:

25 … 55 °C

Storage temperature:

25 … 70 °C

Dielectric strength:

500 Vac / 1 min. between electronic parts and housing

Insulation resistance:

>20 M



/ 500 Vdc, between electronic parts and housing

Operating distance (typical values):

0: 0.1…4 M on R2

B01: 0.1…3.5 m on R2

C01: 0…60 cm

C10: 0…10 CM

C21: 0…35 cm

D00: 0.5…10 cm

F01/G00: 0…25 m

E01: 30 mm with OF-42 / 100 mm with OF-43

T01: 0.1…1 m on R2

B01: 0.1…2 m on R2

C01: 0…35 cm

C10: 0…8 cm
D00: 0…8 cm

F01/G00: 0…20 m

T01: 0

.1…1 m on R2

Emission type:

red (630 nm) (mod. D00/E01) / red (660 nm) (mod.B01/T01)

infrared (880 nm) (mod. A00/C01/C10/C21/G00)

Ambient light rejection:

according to EN 60947-5-2

Vibrations:

0.5 mm amplitude, 10 … 55 Hz frequency, for every axis (EN60068-2-6)

Shock resistance:

11 ms (30 G) 6 shock for every axis (EN60068-2-27)

Housing material:

Nickel-plated brass

Lens material:

PMMA

Mechanical protection:

IP67 Type 1 enclosure

Connections:

2 m cable



4 mm / M12 - 4 pole connector

Weight:

110 g. max. cable vers. / 60 g. max. connector vers.

AtEx 2014/34/EU

II 3D EX tc IIIC IP67 T85°C

SETTING

Setting of S5N-

Mx…A00

Position the sensor and reflector on opposite sides.
Find the points where the yellow LED (OUT) is switched ON and OFF in both vertical and horizontal positions, and fix the sensor in the center
between these points.

Setting of S5N-

Mx…B01/T01

Position the sensor and reflector on opposite sides.

Turn the sensitivity trimmer to the maximum position.
Moving the sensor both vertically and horizontally, determine the power on
and off points of the yellow LED (OUT) and then mount the sensor in the
middle of the points defined. Optimum operation is obtained when the
green LED (mod.B01) is ON and the yellow LED is OFF.

B01 models

: If necessary reduce sensitivity in order to detect very small

targets. In order to improve alignment, repeat the procedure detailed
above whilst progressively reducing the sensitivity.

T01 model

: Turn the sensitivity trimmer counterclockwise

until the yellow LED turns ON

(pos.A).

Turn slowly the trimmer again clockwise until the yellow
LED turns OFF

(Operating condition, pos.B).

Setting of S5N-

Mx…F01/G00/E01 with OF-43 (P/R fibre-optics)

Position the sensors (fibre terminals) on opposite sides.
Turn the sensitivity trimmer to maximum: moving the sensor both vertically
and horizontally, determine the power on and off points of the yellow LED
(OUT) and then mount the sensor in the middle of the points defined.
Optimum operation is obtained when the green LED is ON and the yellow
LED is OFF (the output function and the relative LEDs are inverted in the
E01 model with the OF-43 fibre).
If necessary, reduce sensitivity using the trimmer, in order to detect very
small targets. In order to improve alignment, repeat the procedure detailed
above whilst progressively reducing the sensitivity.

Setting of S5N-

Mx…C01/C21/E01 with OF-42 (proximity fibre)

Turn the sensitivity trimmer to minimum: the green LED is ON, the yellow
LED is OFF. Position the target to detect in front of the sensor or of the
fibre terminals. Turn the sensitivity trimmer clockwise until the yellow LED
turns ON

(Target detected state, pos.A).

Remove the target, the yellow

LED turns OFF. Turn the sensitivity trimmer clockwise until the yellow LED
turns ON

(Background detected state, pos.B).

The trimmer reaches maximum if the background is not detected.
Turn the trimmer to the intermediate position C, between the two positions
A and B. The green LED must be ON.

Setting of S5N-

Mx…C10/D00

The operating distance range of these sensors is factory preset: please
consider this feature when positioning.

TEST FUNCTION (S5N-

Mx…G00)

The TEST+ and TEST- inputs can be used to inhibit the emitter and verify
that the system is correctly operating.
The receiver output should switch when the test is activated while the
beam is uninterrupted.
The inputs activating voltage range is 10 … 30 Vdc.

Datalogic S.r.l.

Via S. Vitalino 13 - 40012 Calderara di Reno - Italy
Tel: +39 051 3147011 - Fax: +39 051 3147205 - www.datalogic.com

Helpful links at www.datalogic.com:

Contact Us,

Terms and Conditions,

Support

For information about the disposal of Waste Electrical and
Electronic Equipment (WEEE), please refer to the website at

www.datalogic.com



Without

limiting  the  rights  under  copyright,  no  part  of  this  documentation  may  be  reproduced,
stored in or introduced into a retrieval system, or transmitted in any form or by any means,
or  for  any  purpose,  without  the  express  written  permission  of  Datalogic  S.p.A.  and/or  its
affiliates.  Datalogic  and  the  Datalogic  logo  are  registered  trademarks  of  Datalogic  S.p.A.  in
many  countries,  including  the  U.S.A.  and  the  E.U.  All  other  trademarks  and  brands  are
property  of  their  respective  owners.  Datalogic  reserves  the  right  to  make  modifications
and improvements without prior notification.

821005714 Rev. E

MIN

MAX