Datalogic Magellan 800i Page 148 Reference Manual Download

Page: 148 / 184

2D Symbologies

140

Magellan

800i

QR Code — continued

QR Code Length 1, Length 2 Programming Instructions

1. Scan the START bar code.

2. Scan either the Set Length 1 or Set Length 2 bar code.

3. Turn to

Alphanumeric Pad

and scan the four digits (zero-padded) representing the length.

Scan the END bar code.

NOTE

For QR Code labels, only the data characters are included in the length
calculations.

Any value set higher than 2710 will be considered to be 2710.

START / END

PROGRAMMING BAR CODES

DEFAULT SETTING FOR THIS FEATURE: 0001

Set Length 1

Set Length 2

DEFAULT SETTING FOR THIS FEATURE: 2710

03DA(CR)

03DB(CR)

Summary of Contents for Magellan 800i

























































































































































































Search results

Summary of Contents for Magellan 800i

Reviews:

Related manuals for Magellan 800i

Brands by name

Popular brands

Datalogic Magellan 800i, Reference Manual

Search results

Summary of Contents for Magellan 800i

Reviews:

Related manuals for Magellan 800i

Brands by name

Popular brands