background image

DX8200A-3002 QUICK GUIDE 

11

 

COMPLIANCE 

 
 
See the DX8200A Reference Manual for the Declaration of Conformity. 
 
 

LASER SAFETY 

 

 

Figure D 

 

Warning and Device Class Label 

1

Device Identification Label 

2

 

 

The scanner is classified as a Class 2 laser product according to EN60825-1 regulations and as a Class II laser 
product according to CDRH regulations. 

 

Disconnect the power supply when opening the device during maintenance or installation to avoid exposure to 
hazardous laser light. 

 

There is a safety device, which allows the laser to be switched on only if the motor is rotating above the threshold 
for its correct scanning speed. 
 
The laser beam can be switched off through a software command (see also the Genius™ Help On-Line). 
 

 

LASER LIGHT 

DO NOT STARE INTO BEAM 

CLASS 2 LASER PRODUCT

 

MAXIMUM OUTPUT RADIATION 1 mW 
EMITTED WAVELENGTH 630~680 nm 

TO EN 60825-1:2001

 

 

 

CAUTION-CLASS 3B LASER LIGHT WHEN OPEN 

AVOID EXPOSURE TO BEAM 

LASER LIGHT EMITTED 

FROM THIS 

APERTURE 

Warning and Device Class Label 

 

Model No. 

Amp. 

Serial No. 

Datalogic Automation S.r.l.  Via Candini,  2 
40012 Calderara di Reno - Bologna - Italy 
Manufactured Volt 

This product conforms to the applicable requirements
of 21CFR1040 at the date of manufacture. 

 

 

Device Identification Label 

 

 
The laser diodes used in this device are classified as Class 3B laser products according to EN 60825-1 regulations 
and as Class IIIb laser products according to CDRH regulations. Any violation of the optic parts in particular can 
cause radiation up to the maximum level of the laser diode (30 mW at 630~680 nm). 
 
 

2

1

Summary of Contents for DX8200A-3002













Reviews: