manualshive.com logo in svg

Datalogic AREAscan DS2-05-07-015-JV, Instruction Manual, Page: 44 / 48

Share
Download
Datalogic AREAscan DS2-05-07-015-JV Instruction Manual Download Page 44

DS2

 

Instruction Manual 

 

40   
 

8.  DIAGNOSTIC FUNCTIONS AND LED INTERFACE ERROR SIGNALLING 

8.1.  Device status visualisation 

The operator can verify the device functioning status using the three LEDs present the receiver unit and 
the one present on the emitter unit. 
 
The meaning of the LEDs present of the receiver unit (RX) depends on the light grid operating mode. 
 

RECEIVING UNIT (RX) 

Signalling 

Status 

 

-  No power supply. 
-  Microprocessor in the reset condition. 
 

 

-  Normal RX functioning 
 

 

-  Presence of object inside sensitive area or units misaligned. 
 

 

-  Short-circuit signalling on switching output 
 

 

-  Generic anomaly on RX unit 
 

 

-  Critical alignment of the TX and RX units or weak received signal. 
 

 

EMITTER UNIT (TX) 

 

Signalling 

Status 

 

Signalling 

Status 

 

-  No power supply. 
-  Microprocessor  in  the 
reset condition. 
 

 

 

-  Generic  anomaly  of 
the TX unit 
 

 

  Normal TX functioning 

 

 

-  No 

synchronism 

between  RX  and  TX 
units 

OFF 

 

OFF

 

OFF 

 

Green ON

 

Red ON 

 

Green ON

 

Red blinking 

 

Green ON

 

OFF 

OFF 

OFF

 

ON or OFF 

OFF 

Green ON

 

Yellow ON 

OFF 

Green ON

 

Yellow ON 

Red blinking 

Green ON

 

OFF 

Red ON 

Green ON

 

OFF or ON 

OFF 

Green blinking

 

Summary of Contents for AREAscan DS2-05-07-015-JV

















































Reviews:

No comments