background image

P T L   C O M P A C T   T Y P E   1   M A N U A L

21

Advanced Manual

 

Manual to assist with higer level set up and 

configuration, test processes.

Aspects 

The actual lights or housing that contains 

the Lights.

 

Beacon 

The orange indicator on the BACK of the 

Traffic lights. 

This is to indicate (from the back) when the 

RED Aspect is ON.

CHN

 

 

Chanel Number used for the Radio Link.

HRC    

Hand-Held Radio Controller.  

This term is interchangeable with PTL 

Remote. 

ID 

 

Identification Number 

0 = Master. 1 or Higher = Slave.

Lights

   

Actual Traffic signal Lamps.   

Red, Yellow and Green.

PTL 

 

Portable Traffic Light. 

PTL-Compact 

A Type-2  PTL Controller

PTL-Stop-N-Go

 

A simplified version of the PTL series of 

products. Can 'only' operate PTL-Type-1.

PTL-Trailer 

A fully autonomous solar powered Traffic 

Light consisting of a Master and Slave set. 

 

PTSU  

Portable Traffic Signal Unit. 

This term is interchangeable with PTL.

PTL Remote 

This term in interchangeable with HRC. 

This is the Hand Held Remote that is used 

to exclusively control all the PTL Signal 

changes, control the Lights ON/OFF 

function as well as other functionality as 

described in this Manual. 

RF 

 

Radio Frequency used for the Radio Link.

SD

 

 

Storage Device Memory Card. Used for 

setup, fault logs, firmware upgrade, 

Bluetooth PIN.

SIG

 

 

Signal Strength used for the Radio Link.

Glossary of Terms and Abbreviations

Summary of Contents for PTL Compact 2
























Reviews: