background image

Dap4 LonWorks Interface Instructions 

Document number 600-000-966 Ver. 3                                                                                                                                                             

7

Description 

Read/

Write

Variable Name 

Data 

Type

LONworks 

SNVT

Cooling Utilization Over Last 
Hour -Percentage of cooling is 
used in the last hour of 
operation; this point applies to 
DX unit. 

R Comp_duty 

I nvoCoolUtlz  8 

Heating Utilization Over Last 
Hour -Percentage of heating is 
used in the last hour of 
operation 

R Heat_duty 

I nvoHeatUtlz  8 

Humidifier Utilization Over Last 
Hour -Percentage of humidifier 
is used in the last hour of 
operation 

R Hum_duty 

I nvoHumUtlz  8 

Compressor 1 Runtime -This 
point applies to DX unit with one 
compressor -high 

R C1_Hours_H 

I nvoC1_Hours_H 

Compressor 1 Runtime -This 
point applies to DX unit with one 
compressor -low 

R C1_Hours_L 

I nvoC1_Hours_L 

Compressor 2 Runtime -This 
point applies to DX unit with 
dual compressor - high 

R C2_Hours_H 

I nvoC2_Hours_H 

Compressor 2 Runtime -This 
point applies to DX unit with 
dual compressor - low 

R C2_Hours_L 

I nvoC2_Hours_L 

Heater 1 Runtime - high 

Ht1_Hours_H 

nvoHt1_Hours_H 

Heater 1 Runtime - low 

Ht1_Hours_L 

nvoHt1_Hours_L 

Humidity upper limit alarm 

Write 
only 

Hum_Hi_SP I 

nviHiHumLimit 

Upper limit alarm of return air 
temp 

Write 
only 

Ret_Air_Hi_SP I 

nviHiTempLimit 

105 

Humidity setpoint 

R/W 

Hum_setpoint 

nvoHumSetpoint / 
nviHumSetpoint 

CW valve open % (0-100% with 
10% increment) 

R CW_disp 

I nvoValve 

Chilled Water Utilization Over 
Last Hour - This applies to 
Chilled water or Energy saver 
units. 

R WtrVlv_duty 

I nvoChillUtlz  8 

Humidifier Runtime - high 

Hum_Hours_H 

nvoHum_Hours_H  8 

Humidifier Runtime - low 

Hum_Hours_L 

nvoHum_Hours_L  8 

Blower Runtime - high 

Blower_Hours_H 

nvoFan_Hours_H  8 

Blower Runtime - low 

Blower_Hours_L 

nvoFan_Hours_L 

Summary of Contents for LonWorks dap4











Reviews: