background image

WARRANTY AND SPECS

SPECIFICATIONS

Input Impedance: 1M

Minimum Load Impedance: 2

Ω

Maximum Power Output: 500 Watts RMS @ 4

 (1khz 

full blast 2 min max) 20%THD
      450 Watts RMS @ 8

Power Amp Input Impedance: 1M

Power Amp Input Level: 2400 mW RMS
Pre-Amp Output Impedance: 1k

Pre-Amp Output Level: 2400 mW RMS

Maximum Power Consumption: approx. 700VA
Forced-air cooled
AC Input Power: 100-250 VAC (Via selector switch on 

left side panel).
Cycles: 50/60 Hz
Dimensions: 18.0 cm x 7.1 cm x 23.0 cm, l x h x w,
(7.1" x 2.8" x 9.1")
Weight: 2.4 kg (5.29 lbs)
Built and Engineered in Helsinki, Finland.
(00358) 504 757005

WARRANTY

Please register for your warranty at 

http://mypedal.darkglass.com. The Alpha·Omega 500 is 

under warranty to the original owner for a period of three 

years against manufacturing defects in the country where 

the product was originally purchased. 

If you experience a problem with the unit, please contact 

[email protected] to receive a Return Authorization 

number or for information on the nearest authorized repair 

center. A copy of your original receipt must be included 

with all warranty repairs. You are responsible for all 

shipping charges. The unit must be shipped to us freight 

prepaid. We will return the unit freight collect. 

Darkglass Electronics OY is not responsible for shipping 

damage either to or from our service center. Claims must be 

filed with the carrier. For repairs please contact your local 

dealer or distributor for your country’s specific warranty 

period and repair procedures.

Alpha·Omega® is a registered trademark of Darkglass 

Electronics OY.

Summary of Contents for Alpha-Omega 500











Reviews: