DAPAudio ORDERCODE D3710 Installation Manual Download Page 8

 

Single Compact Array. 

A single Compact Array may be used on a tripod                   
Stand (DAP Audio D8409B) or on a pole (DAP Audio 
D8404) over its companion subwoofer (the DAP Audio  
(D3701). The use of a subwoofer is recommended for  
applications requiring more low-frequency power and  
extension. Usually, the array configuration Long/Mid- 
Throw switch should be set to the "Mid Throw" position 
if a single speaker is used.  
 
The Compact Array includes a dual angle 36mm pole 
Mount socket. By selecting the appropriate pole socket 
and adjusting the height of the tripod or pole, optimum 
coverage may be achieved. Ideally, the audience should 
not be able to see either the bottom or the top surface of  
the speaker. This will insure that all listeners are within the  
“included coverage angle” of the speaker. The rear  
pole-socket will position the speaker with the baffle 2.5º to 
the floor while the forward socket.  
 
System illustration shows availlable DAP Audio D8404 pole.  

 

 

 

 

 

 

 

 

 

 

 

 

 

  

Fig. 2                                                                                                

 

Warning: 

Do not stack more than one D3710 Compact Array speaker  

 

 

 

 

   

on a pole.

 

 

 

               

 

 

 

 

Dual Compact Array 

The Compact Array is designed in such a way that a pair of  
speakers may be safely mounted onto a tripod stand  
(DAP D3710). For most applications the forward socket of the  
compact array will be used. This will tilt the lower of the two  
speakers at a 15° down-angle (providing coverage of the near  
listeners) while the upper speaker will face straight out  
(covering the more distant areas). Ideally, the listeners should  
not be able to see either the bottom or the top surfaces of the  
two speaker array. Usually, the array Long/ Mid- throw switch  
on the lower speaker should be set to “Mid Throw” (0dB) position  
while the upper speaker’s Long/Mid Throw switch should be set to  
“Long Throw” (+3dB) position.

       

 

Place the speakers on the tripod one at a time. Be sure to lock 
the two speakers together using the internal rigging hardware 
(see figure 3). System illustration shows availlable DAP Audio 
D8409B Tripod and D3701 LB-184 bass cabinet.  
 

Warning: 

Do not stack more than two D3710 Compact Array speakers on  
a tripod.                                                                                                 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

  

Fig. 3 

 
 

 

Summary of Contents for ORDERCODE D3710














Reviews: