background image

 

 

INSTALLATION 

INFORMATION 

SMOKE DISCHARGE 

 
Fume exhaust connection position and example of connection to the flue: 

 

 

 

1. 

Condensate discharge fitting

, necessary to prevent any condensate that has formed 

in the flue to flow inside the heat exchanger. 

 
 

 

  The  exhaust  pipe  and  the  flue  connector  should  be  made  in  compliance  with  the  Regulations 

and  Laws  in  force.  They  should  be  made  up  of  metal  and  stiff  ducts,  capable  of  resisting  to 
mechanical, thermal and chemical stress caused by the combustion. 

  It is mandatory that all components of the flue be certified 

 

  To  avoid  reflux  of  condensation  from  the  flue  to  the  hot  air  generator,  there  must  be  a 

condensation discharge at the lowest point of the smoke duct. 

  The weight of the entire smoke duct must not rest on the appliance. 

  The  flue  must  ensure  the  minimum  depression  required  by  the  current  technical  standards, 

considering "zero" pressure to the connection with the fume duct. 

  Non insulated exhaust pipes might be a source of dangers. 

  Unsuitable  or  wrongly  sized  flues  or flue gas  pipes  might  amplify  the  burning  noise  and  affect 

negatively the combustion parameters. 

  Joint seals should be made of materials resistant to the thermal and chemical stress caused by 

the combustion products. 

  If  walls  and/or  covers  have  to  be  crossed,  this  operation  should  be  perfectly  carried  out, 

preventing seepage or fire risks. 

 

 

 

The use of pipes made of plastic material is forbidden 

 

IF INSTALLATION IS PROVIDED IN THE  AREA OF FREE  ACCESS  TO  PERSONS  AND / OR 
ANIMALS,  THE  FLUE  PIPE  UP  TO  APROX.  2  METERS  ABOVE,  MUST  BE  REALIZED  IN 
DOUBLE  WALL  VERSION  AND/OR  EQUIPPED  WITH  ANTI-SCALD  PERFORATED 
NETWORK. 

P

age

.

18

 

Summary of Contents for Master BF 105































Reviews: