Dantel 49013 Installation & Operation Manual Download Page 8

Page: 8 / 10

AGE

49013-1297 <90-00034>

INSTALLATION

Repeat steps 2 and 3 for the other slave locations.

After all slaves have been aligned, remove the level meter.

This completes the alignment procedure.

NOTE:

Do not check the XMT levels at the slave location. These will be
9 dB below the system level when terminated at the slave XMT
test jacks. Using the slave XMT test points to try and set the
same level as the master will magnify and distort the signal
above a maximum level of -1 dB.

. 4 - 49013 M

ODEMS

ASTER

LAVE

PERATION

UPDATED

LOCATION 1

46010

MULTIPLE

ALARM

TRANSMITTER

49013-00

202

MODEM

(MASTER)

P4-2
P4-4

53
54
55
56
36 RCV
18 XMT

600 OHM
BALANCED OUTPUT

600 OHM
BALANCED INPUT

ALARM

POINT

INPUTS

202
TONES

LOCATION 2

LOCATION 3

46010

MULTIPLE

ALARM

TRANSMITTER

49013-00

202

MODEM
(SLAVE)

P4-2
P4-4

ALARM

POINT

INPUTS

36 RCV
18 XMT

46010

MULTIPLE

ALARM

TRANSMITTER

49013-00

202

MODEM
(SLAVE)

P4-2
P4-4

36 RCV
18 XMT

ALARM

POINT

INPUTS

Summary of Contents for 49013











Search results

Summary of Contents for 49013

Reviews:

Related manuals for 49013

Brands by name

Popular brands

Dantel 49013, Installation & Operation Manual

Search results

Summary of Contents for 49013

Reviews:

Related manuals for 49013

Brands by name

Popular brands