manualshive.com logo in svg

Dante DNA3300 Series, Installation And Operation Manual, Page: 94 / 230

Share
Download
Dante DNA3300 Series Installation And Operation Manual Download Page 94

screen prompt, alarm upload, email will not be activated again. After 10s, if system detects another 

alarm signal, it can generate an alarm since the anti-dither time is out. 

  Alarm output: The number here is the device alarm output port. User can select the corresponding 

ports(s) so that system can activate the corresponding alarm device(s) when an alarm occurred.   

  Latch: When the anti-dither time ended, the channel alarm user select in the alarm output may last 

the specified period. The value ranges from 1 to 300 seconds. This function is not for other alarm 

activation operations. The latch is still valid even user disable the alarm event function directly.   

  Show message: System can pop up a message to alarm user in the local host screen if user enabled 

this function. 

  Alarm upload: System can upload the alarm signal to the network (including alarm centre and the 

WEB) if user enabled current function. System only uploads the alarm channel status. User can 

go to the WEB and then go to the Alarm interface to set alarm event and alarm operation. Please 

go to the Network interface to set alarm centre information.   

  Send email: System can send out the alarm signal via the email to alert user when alarm occurs. 

Once user enable the snap function, system can also send out an image as the attachment. Please 

go to the Main Menu->Setting ->Network->Email interface to set.   

  Record channel: user can select proper channel to record alarm video (Multiple choices).   

  User need to set alarm record mode as Schedule in Record interface (Main 

Menu->Advanced->Record). Please note the manual record has the highest priority. System 

record all the time no matter there is an alarm or not if user select Manual mode.   

  Now user can go to the Schedule interface (Main Menu->Setting->Schedule) to set the record 

type, corresponding channel number, week and date. User can select the record 

type:Regular/MD/Alarm/MD&Alarm. Please note, user can not select the MD&Alarm and MD(or 

Alarm) at the same time.   

  Now user can go to the Encode interface to select the alarm record and set the encode 

parameter (Main Menu->Setting->Encode).   

  Finally, user can set the alarm input as the local alarm and then select the record channel. The 

select channel begins alarm record when an alarm occurred. Please note system begins the 

alarm record instead of the MD record if the local alarm and MD event occurred at the same 

time.   

  Tour: Here user can enable tour function when an alarm occurs. System supports 1/8-window tour. 

Please go to chapter4.6.4.2 Display for tour interval setup. Please note the tour setup here has 

higher priority than the tour setup user set in the Display interface. Once there two tours are both 

enabled, system can enable the alarm tour as user set here when an alarm occurred. If there is no 

alarm, system implements the tour setup in the Display interface.   

  Snapshot: User can enable this function to snapshoot image when an alarm occurs. 

  Buzzer: Highlight the icon to enable this function. The buzzer beeps when an alarm occurs. 

 

Summary of Contents for DNA3300 Series







































































































































































































































Reviews:

No comments