background image

 

DLR-6/6P Low-Rise Scissor Lifts 

30

 

P/N 5900254 — Rev. A — September 2020 

Lubrication 

The following drawing shows the lubrication points for the Lift. Note that some lubrication points are 

under other parts of the Lift. 

 

Troubleshooting 

The Lift uses electrical and pneumatic energy; if your organization has Lockout/Tagout policies, 

implement them before performing any troubleshooting. 

Important

If your Lift is not functioning correctly, you must take it out of service until it is fixed. 
All repair work must be done by qualified personnel. 

Issue 

Action to Take 

Platforms move erratically 

or squeak when in use. 

Move the Platforms up and down a few times, with a break between 

each; there could be residual air in the Hydraulic System. 

Platforms do not go up or 
down. 

Make sure the Power Unit is connected to an appropriate power 
source. 
Make sure the Hydraulic Hoses are not pinched or leaking. 
Make sure there is sufficient Hydraulic Fluid in the reservoir on the 

Power Unit. 

Vehicle with no tires is fully 

lowered, Lift will not go up. 

Too much weight on the Frames; no room to get upward motion 

started. Refer t

Vehicle with No Tires Fully Lowered

. 

Hydraulic Fluid is old or 

dirty. 

Replace the dirty fluid with clean, approved Hydraulic Fluids, such as 

Dexron III, Dexron VI, Mercon V, Mercon LV, Shell Tellus S4 / S3 / 
S2, or comparable. 

Platforms make odd noises 

when in use. 

Lubricate hinge points using white lithium grease. 

Platforms are slowly 

lowering on their own. 

Make sure both Platforms are engaged on Safety Locks (if not, 

Hydraulic Fluid could be leaking out, lowering the Platforms). Only 

leave the Lift either fully lowered or engaged on a Safety Lock. 

If you continue to have problems with your Lift, contact your dealer, visit 

dannmar.com/support

email 

[email protected]

, or call 

(877) 432-6627

Summary of Contents for DLR-6









































Reviews: