background image

DANIELS

DANIELS

ELECTRONICS LTD.

ELECTRONICS LTD.

TM

TM

TN100 System Installation and Troubleshooting

MT-3 Radio Systems

1.0

Motherboard

1.1

Modules Do Not Fit in Subrack

1.  Check the guide rail positions (refer to the SR-3 subrack instruction manual).  Relocate the guide rails
if required.

2.  Check the connectors on the back of the module for bent pins.  Carefully straighten any bent pins if
required.

1.2

No Supply Power

1.  If a system monitor is part of the radio system, a quick check for power is to turn the audio switch to
either A or B.  If the LED turns on, power is present.

2.  Inspect all power connections for continuity, polarity, etc.

3.  Check the fuse on the M-3 Motherboard and replace if necessary (standard 15 amp fast blow).  If fuse
blows again go to section 1.3.

4.  Check any fuses outside of the radio subrack(s) and replace if necessary.  If fuse blows again go to
section 1.3.

5.  Check the subrack power input (terminal strip J8) and any batteries and/or power supplies for correct
voltages.  There should be +10 to +17 Vdc at the power input.

6.  Measure the battery voltage at the system monitor if one is installed.  Select the supply voltage func-
tion on the system monitor rotary switch and measure the voltage at the front panel test jacks.  There
should be +10 to +17 Vdc at this point.

7.  If a system monitor is part of the radio system, jumper JU40 is usually not installed.  Power is then
routed through the system monitor.  If the system monitor is not plugged in, the other modules will not
have power.  Ensure the system monitor is installed correctly.

Operational Troubleshooting

Page 5 of 9

43 Erie Street

Toll Free

Canada & U.S.A.

International

Internet

Victoria, B.C.

Phone:

1-800-664-4066

Phone:

250-382-8268

e-mail:

[email protected]

Canada V8V 1P8

Fax:

1-877-750-0004

Fax:

250-382-6139

web:

www.danelec.com

TECHNICAL NOTES

TN100  Rev 3-0-0  Sep 08

© Copyright 2008 Daniels Electronics Ltd. All rights reserved.

TT

hh

iiss

pp

rroo

dd

uu

cc

tt

hh

aa

ss

bb

ee

ee

nn

dd

iiss

cc

oo

nn

ttii

nn

uu

ee

dd

aa

nn

dd

iiss

nn

oo

lloo

nn

gg

ee

rr

mm

aa

nn

uu

ffaa

cc

ttuu

rree

dd

bb

yy

DD

aa

nn

iiee

llss

EE

llee

cc

ttrr

oo

nn

iicc

ss

LL

ttdd

..

Summary of Contents for MT-3 Series










Reviews: