P
I
02 9604 1226 E
I
|
danielaappliances.com.au
PA G E 1 7
P
I
02 9604 1226 E
I
|
danielaappliances.com.au
PA G E 1 6
TURNING ON THE APPLIANCE
STARTING A CYCLE WASH
•
Draw out the lower and upper basket, load the dishes and push them back. It is
recommended to load the lower basket first, then the upper one (see the section entitled
Loading the Dishwasher).
•
Pour in the detergent (see the section entitled Detergent and Rinse Aid).
•
Insert the plug into the socket. The power supply is 220-240 VAC /50 HZ, the specification
of the socket is 10A 250VAC. Make sure that the water supply is turned on to full pressure.
•
Close the door, press the On/Off button to switch on the machine.
•
Press the program button , the wash program will be changed as follows direction:
ECO->Glass->90 Min->Rapid->Soak->Auto->Intensive->Heavy->ECO;
If a program is selected, the response light will light on. Then press the Start/Pause button,
the dishwasher begins to start.
NOTE:
When you press the Start/Pause button to pause during washing, the LED display will
stop blinking and the dishwasher will mooing every minute unless you press the Start/Pause
button to start.
CHANGE THE PROGRAM
1.
A cycle that is underway can only be modified if it has only been running for a short time.
Otherwise, the detergent may have already been released, and the appliance may have
already drained the wash water. If this is the case, the detergent dispenser must be refilled
(see the section entitled “Loading the Detergent”).
2.
Press the Start/Pause button, the machine will pause, press the program button more than
three times then you can change the program to the desired cycle setting (see the section
entitled “Starting a wash cycle”).
NOTE:
If you open the door during a wash cycle, the machine will pause. The LED display will
stop blinking and the buzzer will mooing every minute unless you close the door. After you close
the door, the machine will keep on working after 10 seconds.
FORGOT TO ADD A DISH
A forgotten dish can be added any time before the detergent cup opens.
1.
Press the Start/Pause Button to stop the washing.
2.
Open the door a little.
3.
After the spray arms stop working, you can open the door completely.
4.
Add forgotten dishes.
5.
Close the door
6.
Press the Start/Pause Button, the dishwasher will run after 10 seconds.
AT THE END OF THE WASH CYCLE
When the working cycle has finished, the buzzer of the dishwasher will sound for 8 seconds, then
stop. Turn off the appliance using the ON/OFF button, shut off the water supply and open the
door of the dishwasher.
Wait for a few minutes before unloading the dishwasher to avoid handling the dishes and utensils
while they are still hot and more susceptible to breakage. They will also dry better.
SWITCH OFF THE DISHWASHER
The program light is on but is not blinking, only in this case the programme has ended.
1.
Switch off the dishwasher by pressing the On/Off Button.
2.
Turn off the water tap!
OPEN THE DOOR CAREFULLY
Hot dishes are sensitive to knocks. The dishes should therefore be allowed to cool down around
15 minutes before removing from the appliance.
Open the dishwasher’s door, leave it ajar and wait a few minutes before removing the dishes.
In this way they will be cooler and the drying will be improved.
UNLOADING THE DISHWASHER
It is normal that the dishwasher is wet inside.
Empty the lower basket first and then the upper one. This will avoid water dripping from the
upper Basket onto t he dishes in the lower one.
WARNING!
It is dangerous to open the door when washing, because the hot water may scald you.
10
10
When the working cycle has finished, the buzzer of the dishwasher will sound for 8 seconds, then stop. Turn off
the appliance using the ON/OFF button, shut off the water supply and open the door of the dishwasher.
Wait for a few minutes before unloading the dishwasher to avoid handling the dishes and utensils while they
are still hot and more susceptible to breakage. They will also dry better.
Switch Off the Dishwasher
The program light is on but is not blinking, only in this case the programme has ended.
1.Switch off the dishwasher by pressing the On/Off Button.
2.Turn off the water tap!
Open the door carefully.
Hot dishes are sensitive to knocks. The dishes should therefore be allowed to cool down around 15 minutes
before removing from the appliance.
Open the dishwasher's door, leave it ajar and wait a few minutes before removing the dishes. In this way they
will be cooler and the drying will be improved.
Unloading the dishwasher
It is normal that the dishwasher is wet inside.
Empty the lower basket first and then the upper one. This will avoid water dripping from the upper Basket onto
the dishes in the lower one.
Forgot to Add a Dish
Forgot to Add a Dish
If you open the door during a wash cycle , the machine will pause. The LED display
will stop blinking and the buzzer will mooing every minute unless you close the door .
After you close the door ,the machine will keep on working after 10 seconds.
NOTE:
NOTE:
At the End of the Wash Cycle
At the End of the Wash Cycle
A forgotten dish can be added any time before the detergent cup opens.
Add forgotten dishes.
Close the door
After the spray arms stop working, you can open the door
completely.
2
3
Open the door a little .
1
4
5
6
Press the Start/Pause Button to stop the washing.
Press the Start/Pause Button, the dishwasher will run
after 10 seconds.
WARNING!
WARNING!
It is dangerous to open the door when washing,
because the hot water may scald you.
Change the Program
Change the Program
Premise:
A cycle that is underway can only be modified if it has only been running for a short time. Otherwise, the
detergent may have already been released, and the appliance may have already drained the wash water.
If this is the case, the detergent dispenser must be refilled (see the section entitled " Loading the
Detergent " ).
Press the Start/Pause button , the machine will pause, press the program button more than 3s then you
can change the program to the desired cycle setting (see the section entitled " Starting a wash cycle" ).
1
2
When you press the Start/Pause button to pause during washing, the LED display will
stop blinking and the dishwasher will mooing every minute unless you press the
Start/Pause button to start.
NOTE:
NOTE:
10
10
When the working cycle has finished, the buzzer of the dishwasher will sound for 8 seconds, then stop. Turn off
the appliance using the ON/OFF button, shut off the water supply and open the door of the dishwasher.
Wait for a few minutes before unloading the dishwasher to avoid handling the dishes and utensils while they
are still hot and more susceptible to breakage. They will also dry better.
Switch Off the Dishwasher
The program light is on but is not blinking, only in this case the programme has ended.
1.Switch off the dishwasher by pressing the On/Off Button.
2.Turn off the water tap!
Open the door carefully.
Hot dishes are sensitive to knocks. The dishes should therefore be allowed to cool down around 15 minutes
before removing from the appliance.
Open the dishwasher's door, leave it ajar and wait a few minutes before removing the dishes. In this way they
will be cooler and the drying will be improved.
Unloading the dishwasher
It is normal that the dishwasher is wet inside.
Empty the lower basket first and then the upper one. This will avoid water dripping from the upper Basket onto
the dishes in the lower one.
Forgot to Add a Dish
Forgot to Add a Dish
If you open the door during a wash cycle , the machine will pause. The LED display
will stop blinking and the buzzer will mooing every minute unless you close the door .
After you close the door ,the machine will keep on working after 10 seconds.
NOTE:
NOTE:
At the End of the Wash Cycle
At the End of the Wash Cycle
A forgotten dish can be added any time before the detergent cup opens.
Add forgotten dishes.
Close the door
After the spray arms stop working, you can open the door
completely.
2
3
Open the door a little .
1
4
5
6
Press the Start/Pause Button to stop the washing.
Press the Start/Pause Button, the dishwasher will run
after 10 seconds.
WARNING!
WARNING!
It is dangerous to open the door when washing,
because the hot water may scald you.
Change the Program
Change the Program
Premise:
A cycle that is underway can only be modified if it has only been running for a short time. Otherwise, the
detergent may have already been released, and the appliance may have already drained the wash water.
If this is the case, the detergent dispenser must be refilled (see the section entitled " Loading the
Detergent " ).
Press the Start/Pause button , the machine will pause, press the program button more than 3s then you
can change the program to the desired cycle setting (see the section entitled " Starting a wash cycle" ).
1
2
When you press the Start/Pause button to pause during washing, the LED display will
stop blinking and the dishwasher will mooing every minute unless you press the
Start/Pause button to start.
NOTE:
NOTE:
