background image

Instructions for installation and use 

 

VXe Solo HT

© Danfoss | Produced by Danfoss Redan A/S | 2023.01  | 23

AQ440953137531en-010102

Selected Setting view

You can switch from the performance view to the se-
lected settings view by pressing the push button. The 
LEDs indicate the actual setting. The settings view 
shows which mode controls the circulator. You cannot 
change settings at this stage. After 2 seconds, the dis-
play switches back to performance view. 

If LED 1 is green, it indicates operation or internal con-
trol.
 If LED 1 is red, it indicates alarm or external control.
LED 2 and 3 indicate the different control modes and 
LED 4 and 5 indicate the different curves.

Setting the control mode

Check the pump setting by pressing the button once 
(one constant pessure). The LEDs will briefly (2 sec.) 
show the pump setting before changing back to show-
ing the power consumption. 

See fig. 5 - Pump setting view.

If the pump setting does not give the desired distribu-
tion of heat in
the rooms of the house, change the pump setting. 

See fig. 5 - Pump setting view.

Before starting the setting, make clear what the dis-
play should show for the new setting (

see fig. 5

).

To change the pump setting, choose the setting you 
want (see fig. 5), press the button down for more than 
2 seconds (less than 10) and the pump switches to 
setting selection, the LEDs start flashing and display 
the current setting. Then press the button until the 
LEDs shows the desired setting. The LEDs flash and 
when they stop the new setting is saved. The LEDs 
return to show power cunstumption. 

Please note

 that if the LEDs do not flash after 2 sec-

onds, possibly the pump setting is locked. To unlock, 
press the button down for more than 10 seconds. LEDs 
will flash and the pump is unlocked. To lock the pump, 
repeat the procedure.

For more information, se enclosed Grundfos in-
structions.

12. HEATING CIRCUIT, PUMP

Fig. 4. Selected setting view

Abb. 7. Toggling the settings of UPM3 FLEX AS

Note:

 

As appears in fig. 4, the example of ”performance” and ”selected setting” 

shows: 

• ”performance” - medium/high performance 50 % ≤ P1 ≤ 75 % 

• ”selected setting”- PWM A profile

LED

1

LED

2

LED

3

LED

4

LED

5

PWM profile A

Curve 1

Curve 2

Curve 3

Fig. 5. Pump setting view

Fig. 6. Setting the Control mode

Summary of Contents for VXe Solo HT





































Reviews: