Danfoss Termix VVX-I Installation Manual Download Page 9

Page: 9 / 24

Installation Guide

Termix VVX-I

5.2 Schematic diagram

DHW

DCW

Supply

HE
Supply

Return

HE
Return

Your substation might look different than the schematic diagram shown.

Schematic description

A Heat exchanger, HE

10 Circulation pump

31 Differential pressure controller

Heat exchanger, DHW

14 Sensor pocket, energy meter

38 Expansion tank

Ball valve

18 Thermometer

39 Connection closed

Safety valve

20 Filling/drain valve

41 Fitting piece, energy meter

Thermostatic valve

24 Delivered loose with unit

48 Air vent, manual

Strainer

26 Pressure gauge

63 Sieve
74 IHPT controller

DHW:

Domestic Hot Water

DCW:

Domestic Cold Water

DH Supply:

District Heating Supply

DH Return:

District Heating Return

HE Supply:

Heating Supply

HE Return:

Heating Return

5.2.1 Technical parameters

Technical parameters

Nominal pressure:

PN 10 (PN 16 versions are available on enquiry)

Max. DH supply temperature:

120 °C

Min. DCW static pressure:

1.0 bar

Brazing material (HEX):

Copper

Heat exchangers test pressure:

30 bar

Sound level:

≤ 55 dB

Danfoss District Energy

VI.EH.G3.02 / LUK40440

DEN-GT

Summary of Contents for Termix VVX-I

























Search results

Summary of Contents for Termix VVX-I

Reviews:

Danfoss Termix VVX-I, Installation Manual, Page: 9 / 24

Search results

Summary of Contents for Termix VVX-I

Reviews: