manualshive.com logo in svg

Danfoss Termix HD MIX Compact 28, Installation Manual, Page: 19 / 20

Share
Download
Danfoss Termix HD MIX Compact 28 Installation Manual Download Page 19

Installation Guide

Termix HD MIX Compact 28

8.0 Declaration

8.1 Declaration of conformity

8.1.1 Category 0 with electrical equipment

EC – Declaration of Conformity

Gemina Termix A/S
Member of the Danfoss Group
Navervej 15-17
DK-7451 Sunds

Declares on our sole responsibility that the below products:

Substations – Category 0 with electrical equipment,

covered by this declaration are in conformity with the following directives, standards and other normative
documents, provided that they are used according to our instructions.

Machinery Directive 2006/42/EC

DS/EN 60204-1/A1:2009. Safety of machinery –
Part 1 – General Requirements.
DS/EN 12100:2011. Safety of machinery – Risk
assessment.

LVD – Low Voltage Directive – 2006/95/EC

DS/EN 60204-1/A1:2009. Safety of machinery –
Part 1 – General Requirements.

EMC – Directive – 2004/108/EC

DS/EN 61000-6-2/Corr.:2005. Electromagnetic
compatibility – Generic standard: Immunity
industry.
DS/EN 61000-6-3:2007. Electromagnetic
compatibility – Generic standard: Emission for
residential, commercial & light industry.

Sunds – 2013.03.15

Place and date of issue

Claus Gjøderum Mortensen

Quality & Environment Manager

Danfoss District Energy

VI.GP.E1.02 / LUK42860

DEN-GT

19

Summary of Contents for Termix HD MIX Compact 28





















Reviews:

No comments