manualshive.com logo in svg

Danfoss Termix HD MIX Compact 28, Installation Manual, Page: 11 / 20

Share
Download
Danfoss Termix HD MIX Compact 28 Installation Manual Download Page 11

Installation Guide

Termix HD MIX Compact 28

6.1.3 Flow controller with integrated control valve

The controller is a self-acting flow controller with integrated control
valve. The controller closes when set max. flow is exceeded and
can be used in combination with Danfoss electrical actuators with
or with out safety function. Spring return motor can be used as
safety function by power failure.

6.1.4 Electric 2–way motorized valve

Actuators with or without safety function are available for 3-point
controls. Spring-return actuators can be used to provide safety
shut-off in the event of power failure.

6.1.5 Electronic control

Substations with electronic control must be set in accordance with
manufacturer´s instructions.
Where the room temperature is controlled by radiator thermostats,
it is recommended that thermostats be set for minimum
temperature in each room.

Danfoss District Energy

VI.GP.E1.02 / LUK42860

DEN-GT

11

Summary of Contents for Termix HD MIX Compact 28





















Reviews:

No comments