Danfoss PSH051 Application Manuallines Download Page 44

Page: 44 / 60

Application guidelines

FRCC.PC.021.A5.22

Installation

Parallel mounting feet

Tandem kit code numbers

For parallel mounting, rubber grommets and
spacer must be installed below the rails.

These parts are included in the tandem of trio
accessory kit code number 7777xxx described
below.

Tandem piping design recommendations, applicable to all tandem configurations.

When different compressor models are installed
in parallel, in order to balance compressor sump
pressures, it is necessary to use a suction washer

in one of the compressor. This suction washer
is supplied within kits described below. It must
always be installed on compressor 1.

Oil equalisation

1”3/8

Suction

right 2”1/8

Discharge

right 1”3/8

1”5/8

Compressor 2

Compressor 1

1”1/8 (2x)

Suction left

Discharge

left 1”3/8



Grommet sleeve



Flat washer



Rubber washers



Tandem grommet





Rigid spacers



Tandem rail

Included in kit 7777xxx

Supplied with the compressor

Not supplied





HM10x100

tightening

torque

32.4lbf.ft









Tandem model

Compressor 1

Compressor 2

Suction washer (restrictor) kit

Outline drawing

Code nb for ordering

Reference

Diameter (in)

PSH104

PSH051

7777041

Not needed

8556121

PSH115

PSH051

PSH064

7777037

5311570P01

1.22

8556148

PSH130

PSH064

7777041

Not needed

8556122

PSH128

PSH051

PSH077

7777048

5311579P05

1.14

8556148

PSH141

PSH064

PSH077

7777037

5311579P01

1.22

8556148

PSH154

PSH077

7777041

Not needed

8556123

Summary of Contents for PSH051





























































Search results

Summary of Contents for PSH051

Reviews:

Related manuals for PSH051

Brands by name

Popular brands

Danfoss PSH051, Application Manuallines

Search results

Summary of Contents for PSH051

Reviews:

Related manuals for PSH051

Brands by name

Popular brands