background image

User Guide | Gas detecting sensor, type PAGM for CO2 and Halocarbon

© Danfoss | DCS (vt) | 2021.03

BC372016561395en-000101 | 5

PAGM-IR FOR CO2 - ONLY

Important: 

•  The CO2 PGM-IR (PN: 080Z2148) displays CO2 PPM gas readings that are relative to ambient air, NOT 

absolute CO2 PPM readings.

•  If the air in purge air bag is contaminated, use the EMPTY BAG function to clear the bag, then fill the 

bag with clean air.

To turn ON the monitor, lift up the shield located in front of the handle and press the red power ON/

OFF switch.

Important: 

•  The CO2 PAGM-IR (PN: 080Z2148) during warm-up needs to be filled with ambient/clean air (outside 

(prior to CO2 testing.

When the monitor has been powered ON immediately all front panel lights turn ON and a splash 

screen appears showing the monitor’s current firmware revision level. After a brief moment the Warm 

Up screen is displayed along with the front panel ON light (green) blinking allow the monitor it to 

warm up for approx. 5 minutes.

PAGM-IR for halogen gas

After the Warm Up has finished the unit is ready to measure gas, please select the appropriate gas 

using the display menu.

During normal operation Display screen shows when the monitor is performing the following 

functions:
• 

 MEASURE

 indicates that the monitor is actively measuring the refrigerant gas level at the sample 

point. To reset the peak value to zero, press the ENTER button.

•   

PURGE

 is displayed when the monitor is resetting baseline ppm value using fresh Air.

• 

 PRES  CHK 

is displayed when the monitor is performing an atmospheric pressure check, which is 

done to ensure the accuracy of the gas measurement under varying atmospheric conditions. This 

pressure check is performed every 30 minutes.

PAGM-IR for CO2

Important: 

•  The CO2 PGM-IR (PN: 080Z2148) has an internal purge air bag that needs to be filled with ambient/

clean air prior to CO2 testing. This air is used to purge the IR detector of sample gas and establish a 

“zero” ppm baseline. Therefore, for greatest accuracy, it is important to ensure the purge air bag is 

filled with clean ambient air  from outside (away from breathing, car exhaust, etc.). 

•  The CO2 PGM-IR (PN: 080Z2148) displays CO2 PPM gas readings that are relative to ambient air, NOT 

absolute CO2 PPM readings.

•  If the air in purge air bag is contaminated, use the EMPTY BAG function to clear the bag, then fill the 

bag with clean air.

4.  General operation

4.1 

Normal operation

ABSOLUTE

RELATIVE

436 ppm

386 ppm

0 ppm

50 ppm

MEASURE

50 ppm

Relative CO  level in

refrigerant testing area

Absolute

CO  level in

ambient air

386 ppm

Adjusted CO  baseline

0070 pk

CO

CO

Level

Danf

os

s

80G8244

Summary of Contents for PAGM











Reviews: