Danfoss iSave 21 Service Instruction Download Page 4 | Manualshive

Page: 4 / 22

background image

Service instruction

Disassembling and assembling iSave 21

4

180R9219 / 521B1171 / DKCFN.PI.003.K3.02 / 11.2013

3 .

Disassembling the

pressure exchanger

1.

Unscrew the bolts in the flange.

3.

Gently push out the flange.

2.

Screw in the two M8 bolts.

4.

Wet the shaft and shaft seal with clean

filtered water. Gently lever the shaft

assembly free using 2 screwdrivers.

5.

Unscrew the bolts in the flange.

6.

Gently remove the flange.

Note: Loose parts on the inside of the flange .

«
...
2
3
4
5
6
...
»

Summary of Contents for iSave 21























Reviews:

No comments

Related manuals for iSave 21

Brand: UnionSpecial Pages: 56

Movie FL Black E27 Flaps

Brand: Qazqa Pages: 2

Brand: Danelec Pages: 67

Brand: dbx Pages: 12

Brand: dbx Pages: 13

Brand: dbx Pages: 72

Brand: dbx Pages: 11

Brand: dbx Pages: 16

Brand: Hanna Instruments Pages: 2

Brand: Hanna Instruments Pages: 2

Brand: Hanna Pages: 12

Brand: Hanil Pages: 24

Brand: Hanil Pages: 32

Brand: Hanil Pages: 24

Brand: Patty-O-Matic Pages: 28

Brand: Velp Scientifica Pages: 12

Brand: Yamaha Pages: 24

Brand: J&M Pages: 33

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands