background image

Instruction  

INFOCAL 8

DEN-SMT/PL 

 

 

 

 

 

VI.SH.L1.02 

 

 

               Danfoss District Enrgy

8

9.5   Pulse input function module

Module for two additional meters. Pulse input 1 is marked as “I1-   ”, 

input 2 with “I2 -   “. Pulse inputs can be programmed (IZAR@SET) with 

a value: 1, 2.5, 10, 25, 100, 250, 1000, 2500 litre per pulse.

•  Pulse transmitter must be electrically isolated, e.g. Reed contact

•  Possible units are all the energy units available in the meter, the 

volume unit m³ or no unit.

Data is accumulated separately in registers; can be read in the dis-

play  as IN1 and IN2 and can be transferred via the communication 

modules.

9.6   Pulse output function module

The module is equipped with 2 pulse outputs, which can be freely 

programmed using the IZAR@SET software. The outputs are marked 

as “O1 -   “ and “O2 -   “ on the terminal strip and as Out1 and Out2 

on the display.

•  External supply: Vcc = 3-30 VDC

•  Output current ≤ 20 mA with a residual voltage of ≤ 0.5 V

•  Open Collector (Drain)

•  Electrically isolated

•  Output 1: f ≤ 4 Hz Pulse duration: 125 ms ±10 % 

Pulse pause: ≥ 125 ms –10 %

•  Output 2: f ≤ 100 Hz Pulse duration pulse/pause ~1:1

•  The volume pulse rate can be freely programmed

•  Standard: last digit in the display

9.7   Combined function module (IN/OUT)

The combined module has 2 inputs and 1 output.

See chapter 8.5 for the specific characteristics on the pulse input. 

A 3 VDC voltage is connected to the “+” terminal and can be used as

the supply for a flow sensor.

The pulse output has the same characteristics as pulse output 1 speci-

fied under 8.6. It is not, however, electrically isolated.

9.8   Analogue output function module

The module has 2 passive analogue output connections which are 

freely programmable using the IZAR@SET software. On the terminal 

strip, the electrically isolated outputs “1” and “2” are marked and the 

polarity is indicated (“+” and “–”).

•  Passive, external power supply: 10…30 VDC

•  Current loop 4 … 20 mA whereat 4 mA = 0 value; 

20 mA = programmable maximum value

•  Overload up to 20.5 mA, then residual current

•  The module displays errors with 3.5 mA or 22.6 mA 

(programmable)

•  Output values: power, flow, temperatures

9.9   Test output

The internally located test output is intended for testing 

laboratories. The manufacturer supplies two special cables:

1. Volume testing pulse

2. Energy testing pulse

Please refer to the inspection and testing manual for further 

specifications (pulse rate, pulse duration/pause, pulse frequency).

Input frequency

≤ 8 Hz

Min. pulse duration

10 ms

Input resistance

2.2 MΩ

Terminal voltage

3 VDC

Cable length

up to 10 m

                                

                                

                                              

                                      

                                       

The module is connected with the meter electronics by means of

a ribbon cable. The separate plug connector on module slot 2 is

necessary for the perfect functioning of the analogue outputs.

Ensure that the temperature sensors (measurement resistances)

remain in contact without interruption during energy verification.

 

T

T

T

T

Summary of Contents for INFOCAL 8













Reviews: