manualshive.com logo in svg

Danfoss H1P Series, Service Manual

Share
Download
Danfoss H1P Series Service Manual Download Page 49

7. Pull assembly fixture out before installing control screws.

Solenoid shaft

Feedback pin

Adjusting 

screw

(cam)

Maximum

adjustment

less than 120°

Control spool

Remove plug (D065) and verify the swashplate feedback pin is properly positioned between control

feedback arms.

8. Install the control module and six cap screws (D250).
9. Using a 5 mm internal hex wrench, fasten control to pump with screws (D250).

10. Torque screws to 13.3 N•m [9.8 lbf•ft] following torque sequence shown.

1

2

3

6

5

4

Torque sequence

(6 screw control)

D065

For proper neutral adjustment procedure, refer to 

Control Neutral Adjustment

 on page 38 topic.

W

Warning

Calibration of sensor output in vehicle software is mandatory after sensor replacement because output
signal can vary from one sensor to the other.

Automotive Control Repair

Drain pump completely before removing control.

Possible erratic pump operation.
Do not allow metal fragments to fall into control housing. Do not fail to install screen.

Service Manual

H1P 069—H1P 250 Axial Piston Single Pumps

Minor Repair

 

©

 Danfoss | September 2020

AX152886482551en-000504 | 49

Summary of Contents for H1P Series

































































Reviews:

No comments

Brands by name

Popular brands

Load more brands