manualshive.com logo in svg

Danfoss H1P Series, Service Manual

Share
Download
Danfoss H1P Series Service Manual Download Page 41

System Pressure Gauge Ports

System

Port  B 

Servo pressure

port M4

System Port A

Servo pressure

port M4

Servo pressure

port M5

Solenoid C1

Solenoid C2

Gauge port MB

system pressure

Gauge port MA

system pressure

P106 489E

For more information see 

H1P Ports Information

 on page 26.

1. Attach a 50 bar [1000 psi] gauge to each servo pressure port M4 and M5.
2. Attach a 600 bar [10 000 psi] gauge to each system pressure port (MA and MB).
3. Remove servo cylinder locking screws (E350) and plates (E300) from both sides of the pump.
4. Disconnect the control solenoids from the vehicle wiring harness.
5. If using a PWM signal to set mechanical neutral, connect the control solenoids C1 and C2 to the signal

source.

Ensure the source supplies no current to the solenoids until required in the following procedure.

Service Manual

H1P 069—H1P 250 Axial Piston Single Pumps

Adjustments

 

©

 Danfoss | September 2020

AX152886482551en-000504 | 41

Summary of Contents for H1P Series

































































Reviews:

No comments

Brands by name

Popular brands

Load more brands