manualshive.com logo in svg

Danfoss H1P 069, Service Manual, Page: 56 / 67

Share
Download
Danfoss H1P 069 Service Manual Download Page 56

Shaft, Bearing Installation

J100

P106038

J150

J300

J250

J200

J200

Protective

cover

Seal 

installation 

tool

J150

J220

1. Inspect the shaft journals for wear, scratching, and pits.
2. Check the splines for fretting; replace if damaged.
3. Rotate the bearing; if it does not rotate smoothly, replace it.
4. Press bearing (J150) on shaft. Install snap-ring (J300).
5. Install the shaft/bearing assembly into the pump.
6. Rotate the shaft to align it with the block and charge pump splines.
7. Press down on the shaft and replace the inner snap ring (J200).
8. For 80/100, 210/250/280

a) Using a suitable press and tooling, lubricate and install new seal into the carrier, making note of

proper orientation.

b) Install new O-ring on OD of seal carrier.

9. Cover end of the shaft with an installation sleeve to protect the seal during installation.

10. Lubricate the seal. Tap on the seal replacing tool or an appropriate deep-socket to press in the seal.

Service Manual

H1P 069—H1P 280 Axial Piston Single Pumps

Minor Repair

 

56 | 

©

 Danfoss | January 2021

AX152886482551en-000601

Summary of Contents for H1P 069




































































Reviews:

No comments