background image

© Danfoss

 

FT1380 Crimp Machine Operator’s Manual

14 | © Danfoss FT1380 Crimp Machine Operator’s Manual | 2022.12. 

 

AQ435955684211en-000101

Electrical Schematics

Terminal Blocks and Pin Numbers   
(115V and 230V models)

Terminal Block  

 

Pin Number  

 

Voltage    

 

Wire Color 

 

Description 

TB1 

  1 

 

  +12V 

AC 

 

  Black 

 

  From 

transformer 

 

(2 

wires) 

        Black 

 

  To 

work 

light 

TB2 

  2 

  +0V 

AC 

  White 

 

  From 

transformer 

(2 

wires) 

        White 

 

  To 

work 

light 

TB1 

 

  3 

 

  None 

 

  Green 

 

  To 

earth 

ground 

TB2 

  1 

  +4.04V 

DC 

  Orange 

 

  To 

transducer 

TB2  

 

 

       

 

+4.04 to 0.04V DC*    

Red  

 

 

To transducer 

TB2 

 

  3 

 

  +0.04V 

DC 

  Brown 

 

  To 

transducer 

TB2 

 

  4 

 

  +5V 

DC 

 

  Red 

 

  Crimp 

switch 

TB2 

 

  5 

 

  0V 

DC 

 

  White 

  Switch 

common 

TB2 

 

  6 

 

  +5V 

DC 

 

  Red 

 

  Retract 

switch 

TB3 

 

  1 

 

  +24V 

AC 

 

  Orange 

 

  To 

dump 

valve 

TB3 

 

  2 

 

  +24V 

AC 

 

  Red 

 

  To 

motor 

contractor

* The voltage at TB2 pin 2 varies between 4.04V DC and 0.04V DC, depending on the position of the crimp ring.

Summary of Contents for FT1380

















Reviews: