manualshive.com logo in svg

Danfoss EM-PMI540-T3000, User Manual

Share
Download
Danfoss EM-PMI540-T3000 User Manual Download Page 45

Only trained and quali ed personnel familiar with the relevant safety requirements are allowed to operate the electric
machine.

Do not use the electric machine without properly dimensioned and operating cooling system. Maximum operation
temperature, current and rotational speed of the electric machine must not be exceeded to avoid permanent damage.

The surface of the electric machine might be hot. Do not touch the electric machine during operation.

Entanglement hazard! Do not touch the electric machine during operation.

Do not run the electric machine when the heater is in use.

Use sufficient personal protective equipment when you are near the electric machine.

Read the instructions in the manual before you install the electric machine.

Operation conditions

The electric machine should be used for its intended purpose only and within limits speci ed by

the manufacturer, concerning:

Loading.
Cooling.
Speed range.
Service interval.
Ambient condition such as temperature and moisture.

EM-PMI540-T3000

7. Operation

44 | 

©

Danfoss | Produced By: Danfoss Power Solutions | November 2018

| BC265857716810en-000103

Summary of Contents for EM-PMI540-T3000




































































Reviews:

No comments

Brands by name

Popular brands

Load more brands