Danfoss EM-PMI540-T3000 User Manual Download Page 27 | Manualshive

Page: 27 / 67

background image

See the electric machine rating plate and data sheets for weight information.

Lift the electric machine using the correct lifting lugs/eyes only.

Do not go under a lifted load.

Figure 13. Lifting lugs/eyes for lifting slings and lifting position of the machine

Horizontal lifting
For lifting, use the inbuilt lifting eyes in the machine frame.

EM-PMI540-T3000

5. Transportation and storage

26 |

©

Danfoss | Produced By: Danfoss Power Solutions | November 2018

| BC265857716810en-000103

«
...
25
26
27
28
29
...
»

Summary of Contents for EM-PMI540-T3000




































































Reviews:

No comments

Related manuals for EM-PMI540-T3000

Brand: Saito Pages: 4

Brand: Jula Pages: 17

Brand: Ecofly Pages: 20

Brand: LCT Pages: 25

Brand: Magnetic Pages: 24

Brand: Northern Lights Pages: 36

Brand: Northern Lights Pages: 45

Brand: Northern Lights Pages: 56

Brand: MINN KOTA Pages: 3

Brand: MINN KOTA Pages: 4

Brand: Clinton Pages: 24

RolloTube S-line DuoFern

Brand: RADEMACHER Pages: 8

RolloTube Basis

Brand: RADEMACHER Pages: 60

Brand: RADEMACHER Pages: 64

EH12-2, EH17-2, EH25-2

Brand: Robin America Pages: 24

Brand: Robin America Pages: 28

Brand: Yanmar Pages: 142

Brand: Yanmar Pages: 316

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands