Danfoss EKC 313 User Manual Download Page 12

12 

User 

Guide RS8FZ402 © Danfoss 2015-07 

EKC 

313

AD

AP

-K

OOL®

Danfoss can accept no responsibility for possible errors in catalogues, brochures and other printed material. Danfoss reserves the right to alter its products without notice. This also applies to products 

already on order provided that such alternations can be made without subsequential changes being necessary in specifications already agreed.
All trademarks in this material are property of the respecitve companies. Danfoss and Danfoss logotype are trademarks of Danfoss A/S. All rights reserved.

List of literature

Instructions  RI8PB (extract from this manual).

 

Here you can see how controllers are mounted and 

programmed.

Installation guide for extended operation 

RC8AC

Here you can see how a data communication 

connection to ADAP-KOOL® Refrigeration control 

systems can be established. 

Installation  considerations
Accidental damage, poor installation, or site conditions, can give 

rise to malfunctions of the control system, and ultimately lead to a 

plant breakdown.
Every possible safeguard is incorporated into our products to 

prevent this. However, a wrong installation, for example, could still 

present problems. Electronic controls are no substitute for normal, 

good engineering practice.
Danfoss will not be responsible for any goods, or plant compo-

nents, damaged as a result of the above defects. It is the installer's 

responsibility to check the installation thoroughly, and to fit the 

necessary safety devices.

ETS connection

If the distance between EKC 313 and the ETS valve exceeds 5 m a 

filter must be mounted to obtain the correct valve function.

L < 5 m

5 m < L < 50 m

Dimensions

Connection

Type

Description

Code no.

AKA 211

Filter 

4 x 10 mH

084B2238

Ordering

DIN-rail mounting

The filter must be installed close to EKC 313

EX

Explosive application

Here the controller can receive a voltage signal of either 0-10 V or 

1-5 V. 

If the pressure transmitter supplies a current signal, a resistance of 

250 ohm must be installed over the terminals.

The supply must be taken from the zener barrier.

Summary of Contents for EKC 313













Reviews: