background image

Power requirements

N24vdc < 500 ma: (at 200 ma load) Range +20 to

+32 vdc.

Maximum ripple ± 5% pk:
Reverse polarity protected.
Amplifier shuts down below +20 vdc.

Output voltages

At pins B2 and Z2

± 15vdc < 50 ma: Ripple <50 mv pk/pk

(- 15vdc not short circuit protected)

Command signal inputs

Voltage input
Current input

At Pins B6, B8 or Z6: Range ± 10 vdc.
Impedance: 100k ohms.
At pins Z6 and Z8: Range 0 to 20 ma.
Impedance: 249 ohms.

Output current drive

Jumper selectable (jumper "JP1")

(A) position ± 50 ma

(B) position ± 100 ma
(C) position ± 200 ma

Front panel test points

Tracking error monitor (TP1)
Output current monitor

± 10v full scale: short circuit protected.

1 mv/ma: short circuit protected.

Edge connector monitor points

P.I.D. output monitor
Pre-amp output monitor

At pin B18: ± 10 v at 5 ma

At pin Z26: ± 6 v at 2 ma

Input bias

0 to ± 10 vdc

Output bias

0 to ± 12% of full scale output.

Current limiters

0 to ± full scale output current.

Dither

Amplitude
Frequency

0 to 20% of full scale output current.

50 to 400 hz.

Proportional Gain

.1 v/v to 20 v/v

Integral Gain

Low range
High range

0 to 40 v/v-sec

2 to 300 v/v-sec

Derivative Gain

Low range
High range

.05 to .2 v-sec/v

.3 to 2 v-sec/v

Pre-amp Gain

1 to 15 v/v

Drift over operating temperature range

< ± .03% of full scale output at maximum gain

Operating temperature range

0 to 50°C

Storage temperature range

-25 to 85°C

Installation Guide

Servo Amplifier

Operating Data

 

©

 Danfoss | August 2023

BC459665217198en-000101 | 7

Summary of Contents for EEA-PAM-591-A-10




















Reviews: