background image

ECtemp 330 (-10 to +10°C)

Installation Guide

8

Warranty

A 2-year product warranty is valid for:

•  thermostats: ECtemp 330 (-10 to +10°C).

Should you, against all expectations, experience a problem with your Danfoss 
product, you will find that Danfoss offers Danfoss warranty valid from the 

date 

of purchase

 on the following conditions: During the warranty period Danfoss 

shall offer a new comparable product or repair the product if the product is 
found to be faulty by reason of defective design, materials or workmanship. The 
repair or replacement.

The decision to either repair or replace will be solely at the discretion of Dan-
foss. Danfoss shall not be liable for any consequential or incidental damages 
including, but not limited to, damages to property or extra utility expenses. No 
extension of the warranty period following repairs undertaken is granted.

The warranty shall be valid only if the WARRANTY CERTIFICATE is completed 
correctly and in accordance with the instructions, the fault is submitted to the 
installer or the seller without undue delay and proof of purchase is provided. 
Please note that the  WARRANTY CERTIFICATE must be filled in, stamped and 
signed by the authorized installer performing the installation (Installation 
date must be indicated). After the installation is performed, store and keep the 
WARRANTY CERTIFICATE and purchase documents (invoice, receipt or similar) 
during the whole warranty period.

Danfoss warranty shall not cover any damage caused by incorrect conditions of 
use, incorrect installation or if installation has been carried out by non-author-
ized electricians. All work will be invoiced in full if Danfoss is required to inspect 
or repair faults that have arisen as a result of any of the above. The Danfoss 
warranty shall not extend to products which have not been paid in full. Danfoss 
will, at all times, provide a rapid and effective response to 
all complaints and inquiries from our customers.

The warranty explicitly excludes all claims exceeding the 
above conditions.

For full warranty text please use QR code

Summary of Contents for ECtemp 330













Reviews: