background image

Danfoss District Energy  

DSA 1 MINI - 

16 DEN-SMT/PL 

VM.HE.B2.02 

Danfoss District Energy

Troubleshooting

Problem

Possible cause

Solution

Not enough pressure on the hot water

Strainer in cold water meter clogged.

Clean strainer - possibly in consultation
with the water supply company.

Long waiting time

Circulation pump out of operation

Check whether the pump is running -
whether the pump is receiving power.
Control that there is no air in the pump
housing - see pump manual.

Temperature too low

See “No domestic hot water”.

See “No domestic hot water”.

Non - return valve on the circulation line
defective (leads to mixing - and the 
circulation water pipes become cold 
during tapping).

Replace non - return valve.

Temperature too high

Defective actuator - possibly dirt in the
valve housing.

Check the functions of the actuator -
clean valve seat if required.

Automatic controls wrongly set or 

defective.

Check if the setting of the controller is
correct, - see separate instructions.

Defective immersion sensor.

Replace immersion sensor.

Variations in temperature

Non - return valve on the circulation line
defective (leads to mixing - and the
circulation water pipes become cold 
during tapping).

Replace non - return valve.

Delcining temperature during tapping

Defective or wrongly set differential
pressure controller (set too low).

Check the functions of the differential
pressure controller - clean valve seat and
capillary tubes if required, - air and rinse
capillary tubes.

Automatic controls wrongly set.

Check that the controller has been 
correctly set - see separate instructions.

Immersion sensor placed incorrectly.

Place immersion sensor correctly in 
accordance with the manufacturer 
instructions for the cylinder. 

You may contact Danfoss Redan A/S for

further information.

Calified heating element.

Clean DHW cylinder with acid solution or
replace heating element.

Poor cooling

Calified heating element.

Clean DHW cylinder with acid solution or
replace heating element.

You may check the specifications of the

manufacturer conc. cylinder capacity.

Summary of Contents for DSA 1 MINI



















Reviews: