background image

 

Installation Guide 

DLX seriesL00410622-01 

 

13 

 

Ensure that the conductors are listed for PV applications and the site environment, and 
that they have the correct color coding. 

 
 

2.4. Electrical Installation  

Contact the local utility company for interconnection agreements and power approval 
before connecting to the grid.  
 
Correct electrical connection is critical for achieving a safe, long-term and reliable 
operation of the entire PV system. 
 

 

NOTICE

 

 

Only persons who are qualified to install high voltage electrical equipment and are 
familiar with the electrical regulations applicable to the installation site may install 
the inverter. This is to ensure a safe connection and avoid electrocution! 

 

 

DANGER

 

 

Never work with live wires! All work on the inverter must be performed with 
disconnected terminals, as contact with live wires may cause serious injury or 
death!

 

 
 

2.4.1. Connection Area 

The 

DC connections

 are achieved by the use of a Stringbox with DC switch and three sets 

of DC connectors. The connection of the 

AC and the network 

cables are with screw 

terminals and a RJ45 connector.  

 

 

Figure 2.4.1: Stringbox with DC switch

 

1.

 CAN bus terminal 

2.

 RS-485 terminal 

3

 Ethernet port  

4.

 Internal DC terminal blocks, 

+POS

 

and 

-NEG

 

5.

 Internal DC ground receptacle, 

GND/PE

 

6.

 Stringbox equipped with DC switch  

7.

 Internal AC terminal block 

Summary of Contents for DLX 2.0

















































Reviews: