background image

32 | AX452438944357en-000301

© Danfoss | Climate Solutions | 2023.09

9

Fitting the shaft seal

Position  in 
parts list

Parts list position: 

2010,

 780, 790

Tools: Innensechskantschlüssel 6 mm, torque spanner

Working course

830 

830, 882 

F88:

 850

880

755

780

790

- Push the pressure spring onto the crankshaft. Rotate the spring until the driving catch is engaged in the    
   crankshaft

- Push the guide ring with O-ring and floating ring onto the crankshaft. Rotate all parts until the spring is 

 

   engaged in the guide ring. Avoid scratches on the floating ring!

- Install the shaft seal cover with the seal. The inscription „TOP“ must be at the top

- Press the shaft seal cover onto the bearing flange and tighten the screws

- Turn the crankshaft by hand

- Insert woodruff key / feather key

5 I Assembly of compressor

CAUTION! 

Avoid damages! 

 

Pay attention to the markings, apply a little oil to the parts!

ATTENTION!  The order for assembly of the screws must be observed to avoid damage, 
 

see numbering. The screws are tightened in two passes with different tightening 

 

 torques!

4

8

1

3

7

2

6

5

20 Nm

1. 

2. 

45 Nm

Summary of Contents for BOCK F18







































Reviews: