background image

AK-PC 

572 

User 

Guide RS8KH202 © Danfoss 2019-03 

9

Wizard

Here you will be led through a series of settings, after 
which the controller will be ready for start.
Image 1 of 27 is displayed here.

The following options are available here:
• B HP
• MT + LT

Main Menu

The first setting is the  
Plant type

When the Plant type has 
been selected, it will al-
low several settings to be 
made.
For example:

Continue to the next 
menus.
All settings are explained 
on the pages that follow.

Start screen upon delivery

Set-up overview

There are 2 ways in which the controller can be set up. Select the one that is easiest for you: either “Wizard” or a review of  
“all parameters”.

The default password upon  
delivery is 300. Use the arrow  
keys to set the password. End  
by pressing “Enter” 

Hold “Enter” 

 

down 

for 2 seconds to come to 
password entry

Select a set-up method. End 
by pressing “Enter” 

Operating principles

1. Select position using arrow keys
2. Select using “Enter” 

3. Use the “X” to return

Language

Choose from one of the 
possible languages

Parameter settings

Here is the start image for 
the possible settings.

Summary of Contents for ADAP-KOOL AK-PC 572





























Reviews: