manualshive.com logo in svg

Danfoss 51 Series, Service Manual, Page: 33 / 40

Share
Download
Danfoss 51 Series Service Manual Download Page 33

Repair

Removing the Solenoid Valve
It is not necessary to remove the valve unless it is being replaced.

Individual parts are not available. Replace entire valve.

Solenoid for J1, J2

If replacing the valve, use a 7/8 wrench to remove the valve from the housing.

Solenoid for J3, J4

If replacing the valve, use a 3 mm internal hex wrench to remove screws (M15). Remove the valve.

Control Disassembly

F32

F324

M24

T6

T4

M23

M23A

 M24

U7

N84

M21

M18

M16

M14

M20

N34

N33

N33

N34

M22

M24

M24A

M22A

M24

M24

U6

M151

M150

M1

Z*

G38

G42

G38

G42

G36

N32

M22

M22A

M15

M1

Note: Orifices (T4 and T6) and 
PCOR adjuster (Z*) are
not included in control

J1, J2

J3, J4

The difference
between J3, J4 and 
J1, J2 is the way the solenoid
valve is attached to the housing

P106 406E

N240

Legend

Item

Wrench size

Torque

M15

3 mm internal hex

2.8 Nm [1 lbf•ft]

M1 (J1, J2)

7/8

20 Nm [15 lbf•ft]

M150, M151
(80, 110)

8 mm internal hex

78 Nm [58 lbf•ft]

Service Manual

Series 51 Hydraulic Proportional Controls Service Manual

J1, J2, J3, J4 Controls

11009446 • Rev BA • July 2014

33

Summary of Contents for 51 Series









































Reviews:

No comments