manualshive.com logo in svg

Danfoss 51 Series, Service Manual, Page: 14 / 40

Share
Download
Danfoss 51 Series Service Manual Download Page 14

Optional PCOR Housing

Disassembly

1. Remove plugs (N27). Remove and discard O-rings (N27A).
2. Using a 1 inch wrench, remove plug (N23). Remove and discard O-ring (N23A).
3. Remove locknut (N14).
4. Remove adjustment plug (Z00). Remove and discard O-ring (N16J).
5. Remove spring (N18).
6. Remove spool and spring guide assembly (N20).
7. Remove screws (N29).
8. Remove and discard O-rings (N24P, N82).
9. If present, remove orifices (U6, U7).

PCOR

N82

N29

N20

N14

N18

N16J

Z00

N87

U6

U7

N24P

P106 384E

N23

N27

N27

Legend

Item

Wrench size

Torque

N27

1/8 inch internal hex

7 Nm [4 lbf•ft]

N23

1 inch

40 Nm [30 lbf•ft]

U6, U7

3 mm internal hex

6 Nm [4 lbf•ft]

N29

5 mm internal hex

16 Nm [12 lbf•ft]

N14

1-5/16 inch

N/A

Inspection

Clean and inspect components for damage or foreign material. Replace damaged parts.

Assembly

1. If previously removed, use a 3mm internal hex wrench to install orifices (U6, U7). Torque to 6 N•m [4

lbf•ft].

2. Using petroleum jelly to retain them, install new interface O-rings (N24P, N82).
3. Position PCOR on multiblock. Install screws (N29). Torque using a 5 mm internal hex wrench to 16

N•m [12 lbf•ft].

Service Manual

Series 51 Hydraulic Proportional Controls Service Manual

PCOR

14

11009446 • Rev BA • July 2014

Summary of Contents for 51 Series









































Reviews:

No comments